Can Two Curt Trailer Hitch Receiver and Coupler Lock Sets Be Ordered with Matching Keys

Question

Question:

Can I order two lock sets keyed alike for two different trailers? It would make it easier for having one set of keys for both trailers.

asked by: Jeff K

0

Expert Reply:

The Curt Trailer Hitch Receiver and Coupler Lock Set part # C23086 does not have a keyed alike option so you won't be able to order two sets with the same keys but I do have one that is, the Reese Tow and Store Lock Kit part # RP7014700 so this is what I recommend.

expert reply by: Conner L

0

Answer 1

Yes, you can get all of the locks you have mentioned keyed alike as long as you order from our Keyed Alike locks page. If you order all the locks you need at the same time they will come keyed alike. If you decide you need another lock keyed the same…

view full answer...

Answer 2

I do have options for you but the TowSmart Trailer Coupler Lock Kit part #TS84FR does not have a keyed alike option. The etrailer Hitch Receiver and Coupler Lock Set part #e99039 is a similar kit minus the surround coupler lock which does have a…

view full answer...

Answer 3

While there is an option to get coupler and hitch locks that can be ordered with each of them using the say key, there isn't a way to order the Reese Tow and Store Lock Kit #RP7014700 with a specific key number or multiple kits that have the same…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

Yes, the Replacement Cover #PE48UV will indeed fit the 2018 Ford F-150 extended cab with the 67" bed. This is made to be a replacement cover for the Pace Edwards JackRabbit Retractable Hard Tonneau Cover #311-JRFA05A28 which is specifically for…

view full answer...

Answer 9

I spoke with my B&W representative who confirms that to install their GNRK1121 #BW77FR Turnover Ball hitch on a 2021 Ford F-150, the center of the 4 inch hole for the gooseneck ball would be placed 42-5/8 inches forward of the rear edge of the…

view full answer...

Answer 10

Beds shorter than 8 foot do commonly need a slider hitch David, but a lot of modern fifth wheel trailers are now made with tapered noses to help and in a lot of cases a slider isn't required. So if the trailer you plan to tow has a tapered nose…

view full answer...

Answer 11

Shackle bolts have a nut that needs to get held with a wrench or socket while tightening them down. If you didn't use a wrench or socket when you initially installed the shackle bolts you could go back now with one so that you can tighten them…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Can Two Curt Trailer Hitch Receiver and Coupler Lock Sets Be Ordered with Matching Keys

Products Referenced in This Question

Continue Researching