Boat Trailer Fender # PF775X21W Mounting Bracket and Hardware

Question

Question:

Do you carry the galvanized carrige bolts, washers and nuts to attach the fender to the brackets I have the brackets

asked by: John C

0

Expert Reply:

The Single Axle Trailer Fender - White Plastic - 8" to 12" Wheels - Qty 1 # PF775X21W you asked about uses the Galvanized Steel, L-Shaped, Bolt-On Brackets for Plastic, Single-Axle Fender PF775X21W - Qty. 2 # PF775-BKT-2 but the hardware is not included and we don't carry it. You will need to obtain what you need from a local hardware store.

expert reply by: Jason S

0

click to enlarge

Answer 1

Yes, since the wheels you have now attach to the hub using lug nuts you can go with a wheel that has a larger pilot hole than the previous wheels. You just can't go to a smaller pilot hole. A wheel that attaches using lug nuts centers on the hub…

view full answer...

Answer 2

The Fulton fenders part #F008554 are universal in that they can mount a number of ways depending on the trailer. I attached a picture that shows a very common way. Or you can use L-brackets like part #PF775-BKT-2 which are commonly used as well.

view full answer...

Answer 3

Our most popular set of fender mounting hardware for 13 inch wheels and tires is the Redline bracket kit part #PF775-BKT-2 which is a set of two L-brackets you could use on your trailer.

view full answer...

Answer 4

You can use the Galvanized Steel, L-Shaped, Bolt-On Brackets, #PF775-BKT-2, if you determine that they will fit the fenders and your trailer. The fenders we carry do not come with brackets because every trailer is different. I have included a picture…

view full answer...

Answer 5

You can mount the fenders directly to the trailer frame through the fender skirt on the back of the fender. I would recommend using large washers if you drill through the fender skirt and attach the fender directly to the trailer frame. If mounting…

view full answer...

Answer 6

To install the fender part #F008559 with the brackets #PF775-BKT-2 you will need to do a bit of modifying as the two can work together, but they are not designed specifically for each other. If you check out the picture I attached you will see how…

view full answer...

Answer 7

We have heard from previous customers that the Fulton replacement fenders part #F008573 that you referenced will fit and replace fenders on a Shorelandr trailer like what you have.

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Boat Trailer Fender # PF775X21W Mounting Bracket and Hardware

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching