Is the Timbren Silent Ride Suspension TSR10KT02 Sold As a Pair

Question

Question:

Is this for a pair or sold single? Thx.

asked by: Bryan H

0

Expert Reply:

The Timbren Silent Ride Suspension part # TSR10KT02 is sold as a pair or in other words it will replace the suspension on a tandem axle trailer. It comes with both sides needed for this. The axle will attach via the two u-bolts on each side.

expert reply by: Conner L

0

Answer 1

If you have 7,000 lb, 3" diameter axles on your 2017 Redwood RV Redwood Fifth Wheel then the Timbren Silent Ride Suspension for Tandem Axle Trailers part #TSR14KT01 is correct not part #TSR7000T05. This is an excellent option to upgrade your…

view full answer...

Answer 2

A Timbren Axle-Less system or Silent Ride system would definitely upgrade the stock leaf spring set up on any camper or trailer. That being said, there are a couple things to keep in mind when choosing one of these systems.. The Timbren Axle-Less…

view full answer...

Answer 3

Really good question as it is pretty confusing, so I reached out to Timbren and 14,000 lbs is the TOTAL capacity of the Timbren Silent Ride Suspension for Tandem Axle Trailers you asked about - Timbren Silent Ride Suspension for Tandem Axle Trailers…

view full answer...

Answer 4

This particular model of the Silent Ride suspension, #TSR14KT01, is rated for 14,000 pounds and has a 3 inch round axle seat. I have included a picture that shows all of the important measurements for this unit for you as well. Current pricing is…

view full answer...

Answer 5

For your 2017 Stealth Forest River Toy Hauler that has a GVWR of 12,100 lbs the best Timbren Silent Ride would be the part #TSR14KT01 which has a capacity of 14,000 lbs. This will put the axles of your trailer 6-1/8 inches from the frame which you…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

Hi Bruce, To lift your trailer we'll first need to check of the suspension and see if you have torsion axles or a leaf spring suspension. If you have torsion axles then I'll need to see the axle tag in order to determine what you have so I…

view full answer...

Answer 11

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 12

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Is the Timbren Silent Ride Suspension TSR10KT02 Sold As a Pair

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching