Does Connector Need to Change When Converting to LED Trailer Light

Question

Question:

do I need to change female plug out to a led plug, if I have changed lights out to led

asked by: Phala

0

Expert Reply:

Do you mean the main trailer connector? Or what specifically are you asking about? If you have the standard 3 plug that the # STL53RCB uses like part # A47PB you would not need to replace it as this is not an LED specific connector.

expert reply by: Jameson C

0

Answer 1

You may not even need load resistors to switch to LED lights. The best thing to do is to try the lights without load resistors first. No need to purchase something you may not need until you know need it. Load resistors such as #DI34ZR dissipate heat…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 4

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 5

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 6

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 9

On oil bath hubs the seals are different than standard grease seals. The correct replacement for what you have is #91030. Unitized oil seals like this have a part that stays fixed and a part that rotates with the hub for optimum leak protection. I…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

I checked with Demco and their Tabless Base Plate Kit item #DM29FR is exactly what you need to flat tow your 2023 GMC Sierra 1500 with a Excali-Bar III Tow Bar item #DM9511013. This is custom fit and works with all models of the 2023 Sierra 1500…

view full answer...

Does Connector Need to Change When Converting to LED Trailer Light

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching