Is There a Rackem Grass Catcher for a Kubota Zero Turn Mower

Question

Question:

Will this catcher fit or can it be made to fit a Kubota zero turn

asked by: James S

0

Expert Reply:

I do have Rack'em Grass Catchers for certain Kubota mowers which you can see listed in the photo below. These mowers will use either the Rack'em Grass Catcher part # RCMMS4-OVBS1 or the part # RCMMS4-EXS1. If the model you have is not listed below then there won't be a Rack'em Grass Catcher for this sadly.

expert reply by: Conner L

0

click to enlarge

Answer 1

Since you have the standard deck on your Scag Super Z model SSZ-18CV-48 the Rack'Em Grass Catcher for Scag Lawn Mower with Standard Deck #RCMMS4-OBS1 will fit.

view full answer...

Answer 2

The Rack'em Grass Catcher for Scag Lawn Mower with Velocity Deck #RCMMS4-OVBS1 comes with the faceplate you need along with all hardware needed for installation. The extension you are seeking is the Extension for Rack'em Multi-Mount…

view full answer...

Answer 3

The correct Grass Catcher for your Scag Liberty Z48 is the part #RCMMS4-OBS1.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 9

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more…

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Is There a Rackem Grass Catcher for a Kubota Zero Turn Mower

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching