Is There a Replacement for the Landing Gear Motor MPD71119

Question

Question:

Hello, Are you sure this will fit? My MPD71119 has much shorter mounts...maybe 1/4 inch. The new one seems to have much longer mounts.

asked by: Bailey C

1

Helpful Expert Reply:

Correct, the main difference between the MPD71119 and newer landing gear motors like part # LC141893 is the length of the legs. We do not have a direct replacement for the MPD71119 but we have heard of others using the newer landing gear motors like part # LC141893 and trimming down the legs but that is the only advice I have for you.

expert reply by: Conner L

1

Answer 1

Yes you can absolutely use grade 8 bolts instead of the Replacement 3/8" x 3" Snapper Pin for Lippert Ground Control 3.0 Electric Leveling System #LC225598. You'll just want to make sure the bolts you use are the same 3/8" x…

view full answer...

Answer 2

We do have the correct replacement for your Atwood 71119 landing gear motor, which is what is shown in your photo. The replacement part is the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893. I have added a link to a…

view full answer...

Answer 3

To determine if the Lippert 5th Wheel RV Landing Gear Foot Pad #LC314667 will fit on your von weise landing gear I have some measurements you will need to verify are the same with your landing gear. These feet accept a 3/8" hitch pin and the tab…

view full answer...

Answer 4

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

A tow package for a vehicle is usually a frame mounted trailer hitch and trailer wiring on a vehicle like your 2002 Dodge Dakota. If you have those two things you could pretty easily assume you have the tow package. Or, you can take the VIN of your…

view full answer...

Answer 11

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 12

The best modern day size replacement option we have for a 6.00-16 is a 235/80-16 which measures 30-7/8" diameter x 9-3/8" wide. For this, I recommend the Kenda Karrier ST235/80R16 Radial Trailer Tire with 16" Black Mod Wheel part…

view full answer...

Is There a Replacement for the Landing Gear Motor MPD71119

Product Page this Question was Asked From

Continue Researching