Replacement Foot Pad for Lippert Stabilizer Jack 337199

Question

Question:

LC314667 will these fit 2019 XLR 5th wheel with LCI Power Stabilizer Jack - model #337199 on the rear?

asked by: Dale L

0

Expert Reply:

We have the correct replacement foot pads for your Lippert Stabilizer Jack 337199, but the ones you mentioned will not work with that stabilizer.

Instead, the correct part is the Replacement Foot Assembly for Lippert Components Power Stabilizer Jacks # LC157584.

expert reply by: Kyle S

0

Answer 1

The lock code could be located on the key itself, on the face of the lock core, or one a sticker attached to the lock (see photos). Once you find this you can then order the correct replacement key assuming you have a Global Link, Fastec (FIC),…

view full answer...

Answer 2

On the Lippert High-Speed Power Stabilizer Jack 337199 it would appear that the only parts of the legs that are replaceable are the Electric Stabilizer Jack Support Arm #LC1134122 and the Foot Assembly #LC157584. If the black arms are buckled then…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

For your 2018 Ram 2500 with the factory puck system the best 5th Wheel Hitch is the B&W OEM Companion. If you have the 8 foot bed then you will want the fixed 25K #BWRVK3600 and if you have the short 6-1/2 foot bed you will need the 20K Slider…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Replacement Foot Pad for Lippert Stabilizer Jack 337199

Product Page this Question was Asked From

Continue Researching