Semi-Custom 5th Wheel Trailer Hitch Installation Brackets for a 2010 Dodge Ram

Question

Question:

I am ordering curt universal bed rails and installation instructions say I need to also order the bracket kt #16301, I can not find this on your site?

asked by: JIm J

0

Expert Reply:

The brackets you are looking for are # C16301. I have included a link to the installation instructions for you to view. These brackets are designed to fit 2003-2012 Dodge Ram 2500 and 3500 series trucks.

expert reply by: Michael H

0

Answer 1

The Curt universal fifth wheel rail kit part #C16100 that you referenced can be used in a 2006 Chevy Silverado and would have the same weight rating as any hitch that can fit the rails according to Curt. None of our ISR rail manufacturers will give…

view full answer...

Answer 2

Because of obstructions where the rear frame brackets would mount, the Curt Universal Fifth Wheel Bracket Kit, part #C16100 won't work on your 2015 Ram 1500. You'd need to use a kit with rear brackets to fit around the obstruction,…

view full answer...

Answer 3

Yes, the Curt Universal Fifth Wheel Base Rails with Installation Kit part #C16100 will fit your 2009 Dodge Ram 3500 if you also use the Curt Semi-Custom Fifth Wheel Bracket Kit part #C16301. However, this option will require drilling into the frame…

view full answer...

Answer 4

Because you have the L-brackets it looks like the installation kit you have is the Reese 5th Wheel Install kit part #RP30035. You will need the additional Reese Mounting Bracket part #RP58023 that Mike mentioned as well as the Replacement Hardware…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 9

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 10

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 11

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Answer 12

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Semi-Custom 5th Wheel Trailer Hitch Installation Brackets for a 2010 Dodge Ram

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching