Replacement Tail Light for 2000 TrailStar Bass Tracker Pro Boat Trailer

Question

Question:

I want to know if you have drivers side trailer lense and taillight replacements for 2000 model trail star bass tracker pro 175

asked by: Jeff S

0

Expert Reply:

I looked up some photos of a 2000 TrailStar Bass Tracker Pro Boat Trailer and it most likely uses either the Optronics Combination Trailer Tail Light part # ST16RB for passenger and part # ST17RB for driver side or the Optronics Combination Trailer Tail Light part # ST8RB for passenger side or part # ST7RB for driver.

Unfortunately, you'd have to replace the entire tail light as we'd not have just the lens.

expert reply by: Conner L

0

Answer 1

In order to replace the taillight on a Trail Star Trailer you'd simply find one with the same style (shape/function) and then choose the correct replacement based on size. There are several types of Trail Star Trailers so it would be difficult to…

view full answer...

Answer 2

The older generations of the Wesbar submersible low-profile lights came with sealed light bulb capsules that are not replaceable. If your capsule is sealed, then your best option is to replace the lights with new lights like part #403026 and #403076.…

view full answer...

Answer 3

It sounds like your trailer had a wishbone harness and/or could have multiple ground wires. On a 4-Way trailer end, the one covered pin is the ground. Next to that is the running light pin. The running light pin on some connectors will have more than…

view full answer...

Answer 4

If the right side brake light is still functioning then it's not a bulb issue. Since the stop light is working it has something to do with the trailer wiring on the tow vehicle. Most likely a converter box is at fault. If you get me the…

view full answer...

Answer 5

More than likely the red wire is for power and the black wire is the ground on your light. Assuming your trailer lights follow standard colors like on the #16-4B-1, the red wire on your light will connect to the brown trailer wire which is for the…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...