Troubleshooting ER Error Code on Draw Tite Activator Brake Controller

Question

Question:

What do i need to do? What does this mean?

asked by: Patti

1

Helpful Expert Reply:

The DrawTite Activator 5100 referenced doesn't have a display as it only uses an LED indicator light. If you have a DrawTite Activator with an LED display, you probably have the discontinued 5504.

Assuming that is the case, the "Er" code indicates an internal short and the brake controller will need to be replaced. I have attached the user manual as well as a snip of the troubleshooting chart for you to reference.

A great replacement/upgrade at a similar price point is the Tekonsha # TK63VR. This is a proportional brake controller which aromatically applies the trailer brakes based on the deceleration of your tow vehicle. Because of this, proportional brake controllers help prevent wear on both your trailer's and tow vehicle's brakes. Another great thing is that it will plug right in to the same connection previously used for the old brake controller.

expert reply by: Jameson C

1

Answer 1

The troubleshooting guide for the (discontinued) Draw-Tite Activator II 5500 is actually the same as the Draw-Tite Activator IV #5504. The instructions (with the troubleshooting guide) for the Activator IV are linked for you to reference but I have…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 8

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 9

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 10

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...