Which Curt Trailer Wiring Harness Fits 2020 Chrysler Pacifica Limited

Question

Question:

Does this wiring kit fit 2020 Chrysler Pacifica Limited

asked by: WILLIAM C

0

Expert Reply:

Curt has a trailer wiring kit that is a fit for your 2020 Chrysler Pacifica Limited but it's the part # C56322 and not the # C56399 that you referenced.

Curt also has a hitch that fits your vehicle too with the part # C13383 as well.

expert reply by: Jameson C

0

Answer 1

For your 2020 Chrysler Voyager that has the seventh VIN digit as D the correct trailer wiring install harness is the Curt #C56399.

view full answer...

Answer 2

While the Yakima HoldUp Bike Rack #Y02443 has an anti-rattle setup you will also want to add one to the Curt Multipurpose Ball Mount #D210. The Curt Anti-Rattle Kit #C69HR will fit into the hollow shank on the Multipurpose Ball Mount and allow you to…

view full answer...

Answer 3

I can sympathize as rattling can be just a nightmare when all you want to do is get from Point A to Point B in relative peace. I highly recommend going with an anti-rattle for your 2 inch hitch to help stop the racket, and the best option is from…

view full answer...

Answer 4

Yes, I can confrim for you that the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C56399 WILL fit your 2017 Chrysler Pacifica LX. This connector fits both the LX and the Touring models and will work for you.

view full answer...

Answer 5

The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C56322 is the only fit from Curt for your 2017 Pacifica Limited. The Curt #C56399 you ordered is only a fit for the LX and Touring trim models so it will not fit your…

view full answer...

Answer 6

Yes, the Curt Anti-Rattle Kit for Hollow Shank #C69HR will hold up when pulling your equipment trailer. This will only work on ball mounts for a 2" receiver with a hollow shank. I feel the Blue Ox Hitch Receiver Immobilizer II #BX88224 is the…

view full answer...

Answer 7

A four-pole connector is the connector that gets connected to the trailer wiring from the tow vehicle. It is called a 4-pole connector because the connector has 4 poles that carry 4 different tail light circuits. Most people will store the 4-pole…

view full answer...

Answer 8

This can be frustrating, but I have a solution for you. If your hitch has a lip or collar around the opening, the Roadmaster Quiet Hitch #RM-061 is going to be perfect for you. You can use this clamp when towing a load, carrying a bike rack and also…

view full answer...

Answer 9

The Draw Tite hitch part #76046-SK that fits your 2018 Chrysler Pacifica Hybrid comes with all needed install hardware. You would not need anything else to complete the install.

view full answer...

Answer 10

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 11

The Curt T-Connector Vehicle Wiring Harness #C56399 does not fit your 2017 Chrysler Pacifica Limited, it is for the LX and Touring models; the correct part for your Limited is the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Which Curt Trailer Wiring Harness Fits 2020 Chrysler Pacifica Limited

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching