Trailer Wiring Harness that Fits 2020 Chrysler Voyager

Question

Question:

my seventh vin digit in my 2020 Chrysler voyager is a D can you tell me which trailer wiring harness will fit?? so i can order it.

asked by: Theresa K

0

Expert Reply:

For your 2020 Chrysler Voyager that has the seventh VIN digit as D the correct trailer wiring install harness is the Curt # C56399.

expert reply by: Jameson C

0

Answer 1

It gets a little confusing so I would be happy to help you. The best hitch for a 2021 Chrysler Voyager is going to be the etrailer item #e98903. This hitch is custom fit and bolts to your van with included hardware. I really like this hitch because…

view full answer...

Answer 2

Yes, I can confrim for you that the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C56399 WILL fit your 2017 Chrysler Pacifica LX. This connector fits both the LX and the Touring models and will work for you.

view full answer...

Answer 3

Judging by the photo you've provided (thanks for the photo), you'll likely need the #C56399. Per fit information provided by Curt, the #C56399 which has the gray connectors is supposed to be a fit for the LX and the Touring models.…

view full answer...

Answer 4

Yes, the Curt Anti-Rattle Kit for Hollow Shank #C69HR will hold up when pulling your equipment trailer. This will only work on ball mounts for a 2" receiver with a hollow shank. I feel the Blue Ox Hitch Receiver Immobilizer II #BX88224 is the…

view full answer...

Answer 5

Curt has a trailer wiring kit that is a fit for your 2020 Chrysler Pacifica Limited but it's the part #C56322 and not the #C56399 that you referenced. Curt also has a hitch that fits your vehicle too with the part #C13383 as well.

view full answer...

Answer 6

The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C56322 is the only fit from Curt for your 2017 Pacifica Limited. The Curt #C56399 you ordered is only a fit for the LX and Touring trim models so it will not fit your…

view full answer...

Answer 7

This can be frustrating, but I have a solution for you. If your hitch has a lip or collar around the opening, the Roadmaster Quiet Hitch #RM-061 is going to be perfect for you. You can use this clamp when towing a load, carrying a bike rack and also…

view full answer...

Answer 8

The Draw Tite hitch part #76046-SK that fits your 2018 Chrysler Pacifica Hybrid comes with all needed install hardware. You would not need anything else to complete the install.

view full answer...

Answer 9

As long as you stay under the weight capacity of your 2018 Chrysler Pacifica you are totally safe to tow the trailer weight you mentioned. So a 3,500 lb trailer would be safe to tow with your Pacifica that has a 3,600 lb towing capacity. If you were…

view full answer...

Answer 10

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 11

If you have a hollow shank ball mount you can use this anti rattle device #C69HR. One part will insert into the ball mount shank and you can use the threaded pin to take out the excessive rattling you're experiencing.

view full answer...

Answer 12

The Draw-Tite Ball Mount w/ 2" Ball for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs item #DT49MR you were looking at would work great to haul a 6 x 12 uhaul trailer. The trailer has a maximum 4,400 lbs capacity which would not…

view full answer...

Trailer Wiring Harness that Fits 2020 Chrysler Voyager

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching