Can I Reuse the Metal Portion of my Awning with the New Slide Topper?

Question

Question:

I was looking at LCV000163301 in white. My current topper has a metal beginning that covers the fabric when the slide out is closed. Do I reuse the metal portion of the old awning?

asked by: Daniel B

0

Expert Reply:

The Solera Slide-Topper, part # LCV000163301, does not require the use of the metal weather guards, but since you have them already, It would not hurt to keep them installed to help further the life of the new fabric. The channel of the awning rail is about 3/8 inch wide to hold onto the fabric for comparison to your weather guards.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

For what you are describing, I recommend the LaSalle Bristol XTRM Butyl Tape - 60' L x 3/4" W - Qty 1 #344270341410-1. This tape is a sticky pliable tape that will create a moisture barrier so it will help keep the glass in place for…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 4

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 5

The Carrier Air V RV Air Conditioner is no longer produced so a direct replacement of the same unit is not an option. However, we do have available the two Advent AC models that are designed as replacement units for the Carrier Air V. I recommend…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...