Heavy Duty Skid Rollers for my 45 RV

Question

Question:

Do you have any RV skid rollers that will support a 45 diesel pusher? The ones from Ultra-Fab suggest theirs will not. Thanks!

asked by: Stephen S

0

Expert Reply:

Yes we do have some rollers available for your 45' RV I recommend the Ultra-Fab Steel Jumbo Roller for Trailers and RVs part # UF48-979023. This is a steel roller versus the lighter duty Ultra-Fab Skid Wheels for Low-Profile RVs up to 30' Long part # UF48-979011.

It really depend on exactly how hard you bottom out if they will really hold up or not. Physics right!! I have seen frame mount hitches ripped off of an RV because it bottomed out so hard. With that said these are going to give you the best chance to save your rear end versus the lighter ones available.

expert reply by: Randy B

0

Answer 1

For your 30 foot 5th wheel I really like the frame mount skid wheels that can swivel. For that the Ultra Fab kit part #UF48-979011 would be your best option. I attached a picture that shows these attached to a trailer frame as well. These…

view full answer...

Answer 2

Hello Gaby. I reached out to the manufacturer and found out that the UltraFab Weld-On Jumbo Steel Roller #UF48-979023 uses a 6-1.0mm Zerk fitting. For a replacement you can use the following: - Replacement Brass Grease Zerk for Weld-On Hinges - 6…

view full answer...

Answer 3

The speed rating limitation for a trailer will come down to the tires, it has little to nothing to do with the axle, hub, or wheel size. That said, smaller tires generally do have lower speed ratings but you do not need to upgrade the wheels on…

view full answer...

Answer 4

I certainly do. For this you are going to want to install skid wheels which will take some of the brunt off your trailer. For this I recommend using the Ultra-Fab Steel Jumbo Roller part #UF48-979023. These skid wheels will need to be welded on the…

view full answer...

Answer 5

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 6

The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…

view full answer...

Answer 7

The correct replacement grease seal for the AD2527E you listed is the part #168233.

view full answer...

Answer 8

Thanks for the pictures and all of the information! The correct MORryde pin box for your Forest River is the MORryde Cushioned 5th Wheel Pin Box item #MR83QR you were looking at. This pin box works with trailer's that have a capacity between…

view full answer...

Answer 9

As far as ride quality goes it would be challenging to feel a difference between the Road Armor and MORryde Cushioned Equalizers like part #MR27ZR. I like how heavy duty the MORryde equalizers are made though so since ride quality would be about same…

view full answer...

Answer 10

The hangers you currently have on your trailer are ones I have run into before. That being said, I spoke with MORryde and the #MR27ZR will still fit your trailer, but there is a modification that will need to be made. You’ll have to trim according to…

view full answer...

Answer 11

Yes we do have some rollers available for your 45' RV I recommend the Ultra-Fab Steel Jumbo Roller for Trailers and RVs part #UF48-979023. This is a steel roller versus the lighter duty Ultra-Fab Skid Wheels for Low-Profile RVs up to 30' Long…

view full answer...