Matching Passenger Side Tail Light for LED Trailer Light 328-003-81LBM1

Question

Question:

Product 328-003-81lbm1 led taillight with license plate bracket, trying to find matching light for passenger side ,working on a camper

asked by: Wesley D

0

Expert Reply:

The matching passenger side tail light for the Command # 328-003-81LBM1 is part # 328-003-81BM1.

expert reply by: Carla M

0

Answer 1

The license plate light on the bottom of the LED Trailer Tail Light with License Plate Bracket #328-003-81LBM1 that you referenced is clear incandescent bulb.

view full answer...

Answer 2

While some Solera awning rollers, such as the Solera RV Awning Roller and Fabric, #LCV000211505 that you referenced, have been known to fit some Dometic arms, we cannot confirm all possible configurations will or will not fit. Mixing parts from two…

view full answer...

Answer 3

You could certainly reverse the position of the lamps by installing the #328-003-81LBM1 lamp on the passenger side and the #328-003-81BM1 lamp on the driver's side. Both lamps wire the same way, the white wire is the ground connection, the…

view full answer...

Answer 4

I have another option for you, but the Bargman LED Triple Tail Light - 5 Function - 36 Diodes - White Base - Red and Clear Lens #47-84-530 you were looking at can only be recessed mounted. This light requires a 12-11/16" x 5-1/2"…

view full answer...

Answer 5

There is an LED taillight option that is 8-1/2" x 4" that should be a similar dimension to the taillights on your Keystone Montana (though please measure yours to verify) and have all the functions sans the backup lights (there isn't a…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Yes, because it is a 3-wire light, you can wire the Red Identification Light Bar with White LED Utility Light #OPT88FR to function as rear marker and reverse lights.

view full answer...

Answer 12

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Matching Passenger Side Tail Light for LED Trailer Light 328-003-81LBM1

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching