Are There Instructions for Trimming Skid Plate For Curt Hitch On 2019 Toyota Tacoma TRD Pro

Question

Question:

Are any images available of the amount of trimming required on the skid plate for installation of the C31075?

asked by: Shawn P

0

Expert Reply:

I checked with Curt about installing the Curt Front Mount Trailer Hitch Receiver part # C31075 on a 2019 Toyota Tacoma TRD Pro. In the instructions, there is a cutout diagram for TRD models but this excludes the TRD Pro. Therefore, you will need to test fit the skid plate with the hitch installed before you make the appropriate cuts yourself or you can leave this off altogether.

expert reply by: Conner L

0

Answer 1

I recommend going with the Curt Front Mount Trailer Hitch Receiver #C31075 for your 2021 Toyota Tacoma because it will be easier to install and has the same line pull rating as the Draw-Tite #65070. The only reason I would recommend the Draw-Tite…

view full answer...

Answer 2

I called my contact at Curt and asked about the installation of the front mount hitch #C31075 on your 2017 Tacoma. The two places you mentioned need to be trimmed on the front air dam, but the receiver sits below the air dam so no further trimming is…

view full answer...

Answer 3

You actually will not loose any ground clearance with Curt front mount receiver #C31075 installed on your 2017 Toyota Tacoma. The receiver will not be lower than the lowest part of the front fascia on the truck. I have included a picture showing the…

view full answer...

Answer 4

The easiest to install front mount trailer hitch for a 2018 Toyota Tacoma is the Curt Front Mount Trailer Hitch Receiver part #C31075. It will take less time according to the manufacturer and there is far less hardware involved. I also like Curt more…

view full answer...

Answer 5

For your 2019 Toyota Tacoma the only front hitch we offer has tow hooks on them, the Curt #C31075.

view full answer...

Answer 6

The front end of your 2016 Toyota Tacoma does not need to be disassembled to install the Curt front hitch part #C31075 that you referenced. For the most part the hitch just bolts into place.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Are There Instructions for Trimming Skid Plate For Curt Hitch On 2019 Toyota Tacoma TRD Pro

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching