Replacement Hub for 3,500 lb. Axle

Question

Question:

Can you send me 0ne single axle 3500 lbs kit for this Tire Kenda 205/65-10 Bias Trailer Tire with 10 Galvanized Wheel - 5 on 4-1/2 - Load Range E

asked by: Lili

0

Expert Reply:

If your axle uses the #84 spindle which is very common the Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 5 on 4-1/2 part # AKIHUB-545-35-EZ-K will work for a non braking axle and the Trailer Hub and Drum Assembly - 3.5K E-Z Lube Axles - 10" Diameter - 5 on 4-1/2 part # AKHD-545-35-EZ-K for a braking axle.

expert reply by: Randy B

0

Answer 1

It is ideal to match up the pilot hole size of wheels with your existing hubs since the actual weight load on the wheel is intended to be supported both at the pilot hole and studs, and not just at the studs themselves. If the wheel's pilot hole…

view full answer...

Answer 2

The Load Range E capacity for each tire size represents a different weight capacity but the smallest tire and wheel we offer with the Load Range E is the part #AM3H480 which is 8.4 inches wide and 20.4 inches tall.

view full answer...

Answer 3

Yes, the Kenda 205/65-10 Bias Trailer Tire with 10" White Wheel #AM3H480 is typically used for 3,500 lb axles/hubs which you can see based off of the 1,650 lbs at 90 psi weight rating. Just make sure that your hubs use the 5 on 4-1/2" bolt…

view full answer...

Answer 4

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 5

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 9

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Replacement Hub for 3,500 lb. Axle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching