Replacement 7-Way and 4-Way Connector for 2008 Ford F-450 With Factory Tow Package

Question

Question:

Hi I have a 2008 F450 I need to replace the factory tow plug it has the 4 pin and the 7 way . Also I need to replace the vehicle side of the harness that was also damage to. Thanks

asked by: Garret K

0

Expert Reply:

For a replacement wiring harness for your 2008 Ford F-450 with the factory tow package you need the Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way and 4-Pole Flat Connectors # C55774.

This will plug into your tow package wiring harness and give you a working 7-way and 4-flat.

expert reply by: Kyle S

0

Answer 1

There are a number of possible issues for why the 7-way on your 2011 Ford F-350 may not be working, and I'll go over some things you can check. You started off well by checking the fuses, but since those are good you will need to determine the…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 5

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Replacement 7-Way and 4-Way Connector for 2008 Ford F-450 With Factory Tow Package

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching