EcoHitch Front Mount Receiver for 2020 Ford F-250

Question

Question:

Was wonder if this will fit a 2020 F-250. i would like the hideaway and not below the bumper? thank you

asked by: TRoss M

0

Expert Reply:

According to EcoHitch, their # 306-X7904 front mounted receiver is indeed a fit for the 2020 Ford F-250.

The hitch does sit very nicely in the split on the front bumper, and therefore has a clean look that won't affect ground clearance or the approach angle at the front of the truck.

I've linked to a listing of other accessories available for your 2020 Ford F-250.

expert reply by: Mike L

0

click to enlarge

Answer 1

I spoke with the manufacturer and you move lines to fit the hitch in but there is no relocation or changing of transmission cooler lines to get part #306-X7904 installed on your 2017 F-350.

view full answer...

Answer 2

There is no longer an exclusion for the diesel engines of 2019 Ford F-250 in regards to the fit of the EcoHitch Hidden Front Mount Trailer Hitch Receiver #306-X7904. At one point this hitch did not fit the models of this truck that had diesel…

view full answer...

Answer 3

The EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2" #306-X7904 is a fit with your truck and its components because the hitch does not reach past your sensors. The accessory you use in the hitch will likely cause issues with…

view full answer...

Answer 4

I reached out to EcoHitch and they have not had any report issues when moving the cooler on a 2019 Ford F-250 to install the EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2" #306-X7904. The included brackets do not move the…

view full answer...

Answer 5

The EcoHitch Hidden Front Mount Trailer Hitch Receiver #306-X7904 will require you to use the supplied relocation brackets and move the transmission fluid exchanger. You will open the transmission oil line retainer clip, mount the relocation brackets…

view full answer...

Answer 6

I checked with the manufacturer, who said that these particular locking plates could work with a standard OEM pin box. They are longer and taller than the locking plates that come with a standard hitch and are designed specifically for the Trailair…

view full answer...

Answer 7

If you have destroyed the tail gate on your truck then something is definitely amiss; there is going to be some play in the hitch, but not to the point where a part of your truck would be ruined. You did not specify the hitch you used, but you would…

view full answer...

Answer 8

I attached a picture that shows the install instructions for the Demco capture plate adapter part #DM6171 for you to check out. You do have to remove the old screws to get the old plates off to install this kit.

view full answer...

Answer 9

I had our warehouse measure the Demco Hijacker Autoslide Capture Plates for Trailair Rota-Flex Pin Boxes #DM6171 you were looking at and it is 10-1/4" long x 1-1/2" tall as shown in the included diagram. The #DM6171 is needed when using the…

view full answer...

Answer 10

The Demco Hijacker Autoslide 5th Wheel Hitch w/ Slider #DM8550024 should not be able to be manually turned. The movement of the hitch head side to side is only possible when the weight of the trailer is on the hitch head. The reason for this is so…

view full answer...

Answer 11

Yes, trying to couple at an angle with the Demco Hijacker Autoslide #DM8550034 is actually not recommended. The head is fairly hard to move but you should be able to get it. It'll get easier with use. One method that might help is to lock the…

view full answer...

Answer 12

Great question! The EcoHitch Hidden Front Mount Trailer Hitch Receiver #306-X7904 that you referenced actually installs right behind where the license plate sits (see attached photos). This differs from the Draw-Tite #65076 and the Curt #C31078…

view full answer...

EcoHitch Front Mount Receiver for 2020 Ford F-250

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching