Correct Curt 5th Wheel Install Kit for a 2001 Ford F-250 for Reese Hitch

Question

Question:

Will this work on my 2001 f250 I got Reese hitch well this work

asked by: Matthew G

0

Expert Reply:

The correct Curt Custom Fifth Wheel Installation Kit for a 2001 Ford F-250 is part # C16443-204 which will work just fine with a Reese 5th Wheel Hitch.

expert reply by: Conner L

0

Answer 1

For a true custom fit 5th wheel installation kit that will fit your 2000 Ford F-250 Super Duty with 6-3/4 foot bed I recommend Reese Quick-Install Custom Base Rails and Installation Kit for 5th Wheel Trailer Hitches Item #RP50082-58. Current pricing…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 6

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 7

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 8

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 9

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 10

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 11

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 12

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...