Can Spring Latch be Disassembled

Question

Question:

Can product SL716SS be disassembled for parts? I need the bolt, roll pin, and spring to hold up my trailer gate. The original bolt rusted and broke today. It rusted where the roll pin goes through the bolt.

asked by: Darren

0

Expert Reply:

You should be able to disassemble the Bolt-On Stainless Steel Spring Latch # SL716SS although nobody has tried and tested it for this specific purpose so I can't guarantee you this will absolutely work.

I have added a link to a video review for you to check out as well of the Bolt-On Stainless Steel Spring Latch # SL716SS.

expert reply by: Kyle S

0

Answer 1

I went and pulled a Bolt-On Stainless Steel Spring Latch #SL716SS from our warehouse and measure the dimension you are looking for and found it to be 1-7/8 inches. See the pic I attached, I added the dimension to the picture you submitted

view full answer...

Answer 2

I reached out to Redline for you to get an answer. They informed me that there is no stated weight rating on the Bolt-On Stainless Steel Spring Latch part #SL716SS. It has been designed for use typically in holding doors ramps or windows closed on…

view full answer...

Answer 3

The Bolt-On Stainless Steel Spring Latch, #SL716SS, is sold in quantities of 1. The pin diameter is actually 7/16 inches. I have linked a video review for you. We have another latch option. Weld-on latch #SL58W has a 5/8 inch diameter pin. I have…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 7

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 8

A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…

view full answer...

Answer 9

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 10

Hey Frankie, The bracket for the Timbren Suspension Enhancement System #TFR250SDJ has a locknut in it that makes it feel like the bolt (part #4) is fully tightened when it's not. Their techs have stated that you just have to push past this point…

view full answer...

Answer 11

Hey Paul, we have a Blue Ox base plate kit that fits your 2024 Nissan Versa with the part #BX1856. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle.…

view full answer...

Answer 12

To add a in-bed 7-way to your 2024 Chevy Silverado 2500 to make towing with a 5th wheel easier, I recommend adding the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 7' Long item #C58FV. This harness puts a 4-way and 7-way…

view full answer...

Can Spring Latch be Disassembled

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching