Replacement Mounting Hardware for Thule Hyper XL Cargo Box

Question

Question:

Hello, I recently picked up a used Porsche Thule Hyper XL cargo box and it doesn’t have the correct mounting hardware for my 3.5” Whispbar cross bars. What mounting parts do I need and do you carry them?

asked by: Harold

0

Expert Reply:

The mounting hardware for the Thule Hyper XL TH612 is the part # TH7521484001 which is designed to fit bar dimensions of up to 3-1/2" wide x 1-11/16" tall. If you have bars that are taller than 1-11/16 inches there won't be a way to make the box fit better with modifications.

expert reply by: Jameson C

0

Answer 1

I spoke with my contact at Thule and she confirmed that replacement hinge #TH14936 will fit the Thule Hyper XL TH612. I have included a link to a Video of Replacement Hinge #TH14936 for Thule Cargo Boxes.

view full answer...

Answer 2

Typically, we do not recommend a certain fixed ball mount unless we know both the distance from the ground to the top of the inside edge on the trailer hitch and the distance from the ground to the bottom of the trailer coupler while level. You will…

view full answer...

Answer 3

Yes we still have the 05740 cradles that you referenced, our part number for this product is the #TH8523387001 that you referenced.

view full answer...

Answer 4

The Replacement Thule AcuTight Cradle #TH8523387001 is a single cradle while the Thule Snapfit Cradle Replacement Kit #TH68NB contains 4 cradles and 4 screws.

view full answer...

Answer 5

I can confirm that the Thule Snapfit Cradle Replacement Kit item #TH68NB is the correct replacement part. It fits all of Thule's roof mounted cargo boxes no matter what model. I confirmed this information with Thule. This kit will replace all…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Replacement Mounting Hardware for Thule Hyper XL Cargo Box

Product Page this Question was Asked From

Continue Researching