Is There a Difference Between Buyers Products Pintle Hooks # 337PH55 and # 337PH50

Question

Question:

hi what is the main difference between a 337ph50 buyers hitch and a 337ph55? I know there are more holes but why? they are both rated 50 ton and can take a 20ton young weight. the ph 55 weighs a lot more why? the truck dealer could not answer the questions. thanks

asked by: Fred S

0

Expert Reply:

It's really just a different bolt hole setup for either. The # 337PH50 has 6 bolts and the larger # 337PH55 has a 10 bolt setup. This gives a little more flexibility in how it can mount but overall either will do just as good of a job as the other.

expert reply by: Jameson C

0

Answer 1

The Buyers Products 50 Ton Air Compensated Pintle Hook #337PH50 has a bolt pattern that is 5" on center from the left to right holes. The Top to middle holes are 2-3/8" on center and the middle to bottom holes are 2-1/8" on…

view full answer...

Answer 2

The bolt holes from left to right on the Buyers Products Pintle Hitch Plate Mount part #337PH50 are separated by 5 inches and from the top to middle the distance is 2-3/8 inch and then from middle to bottom is 2-1/8 inch.

view full answer...

Answer 3

The Buyers Products 50 Ton Air Compensated Pintle Hook part #337PH50 measures 2.38" deep by 3" wide. The inner eye diameter is 1.60" wide and 1.37" tall. I contacted Buyers and this hook uses a standard Lunette…

view full answer...

Answer 4

The Buyers Products #3371809042 measures 9-1/2" on the vertical side with the remaining height being 6" down to the bottom. The #3371809043 measures 14-1/2" on the vertical side with 8" of remaining height down to…

view full answer...

Answer 5

The hole spacing of the Buyers Products Fabricators Hitch Plate #3371809042 that you referenced is the same as the standard pintle mount bolt pattern which is 1-3/4 inches apart vertically and 3-1/2 inches apart horizontally.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Is There a Difference Between Buyers Products Pintle Hooks # 337PH55 and # 337PH50

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching