Lock Recommendation for Kuat Transfer 3 Bike Rack TS03G

Question

Question:

I have the Kuat Transfer 3 with an adapter to a 2inch hitch receiver. Does the #HL2 locking hitch pin replace the anti-rattle threaded hitch pin that came with the rack? If so, does the locking hitch pin rattle more than the original anti-rattle hitch pin?

asked by: Garrett G

0

Expert Reply:

We have a lock setup for the Kuat Transfer 3 bike rack with the part # PTSCLK13 but the # HL2 does not fit your rack. This part number comes with a lock for the hitch pin and also comes with cable locks to lock the bikes to the rack as well.

expert reply by: Jameson C

0

Answer 1

We do offer a Kuat hitch lock that will work well to replace your lost hitch pin. For your Kuat Sherpa 2-Bike Rack for 1-1/4 Inch and 2 Inch Hitches, you will want the Kuat Bike Rack Hitch Lock #HL1 or #HL2. This will include both a new hitch pin and…

view full answer...

Answer 2

The Kuat Transfer V2 Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount #KU84FR comes with a tamper-resistant bolt that tightens the carrier to a 2" receiver and you need to use the included security wrench to remove or install. So it…

view full answer...

Answer 3

The etrailer.com hitch part #E98846 is the hitch I recommend for your 2018 Nissan Rogue that has the handsfree lift gate sensors and back up camera. While Nissan recommends a special harness to allow the sensors to still work after a hitch install…

view full answer...

Answer 4

The Thule Helium Pro 3 Bike Rack part #TH9043PRO and Thule Camber 4 Bike Rack part #TH9056 are both excellent options. The main difference between them is weight, the Thule Helium is made of aluminum so it only weighs 20 lbs and the Thule Camber is…

view full answer...

Answer 5

We do! What you'll need to lock your Kuat Transfer V2 Bike Rack for 2 Bikes #KU74FR to your 1-1/4" hitch receiver is the Hitch Lock #HL1. Since the V2 has a built-in anti-rattle system you'll just need a standard Kuat hitch lock without…

view full answer...

Answer 6

The Kuat Cable Lock part #PTSCLK12 that you referenced does not work with the newer V2 style of the Transfer. it only fits the previous generation.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

Answer 12

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Lock Recommendation for Kuat Transfer 3 Bike Rack TS03G

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching