Can Kodiak Disc Brake Kit Fit on Idler Hubs with Vault System

Question

Question:

Our trailer has a vault hub on which the rotor and lugs are one assembly. What do you have to accommodate changeover to a K2R35S while maintaining the Vault system?

asked by: John T

0

Expert Reply:

The Vault style of hub/cap is very similar to the Bearing Buddy setup which we carry. Since the Kodiak Disc Brake Kit # K2R35S is a slip-on style of rotor it would simply fit right onto the idler hubs you have now and your Vault system would be totally fine.

expert reply by: Jameson C

0

Answer 1

I'd be happy to help, but I need to know the capacity of your axle, if you have brakes, and the bolt pattern. The easiest way to get this information is on the axle tag which is located on the center of the axle beam, so sending me a picture…

view full answer...

Answer 2

I went out into our warehouse to grab a Trailer Hub part #AKIHUB-545-35-K that you referenced to measure it and found that it is 6-1/8 inches in overall diameter.

view full answer...

Answer 3

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 4

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...

Answer 5

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 6

On equalizer 013-105-04 in kit #K71-360-00 the eye center to eye center measurement is approximately 7-1/2 inches.

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

For your 4x6 utility trailer, I recommend using the Taskmaster 4.80R12 Radial Trailer Tire part #TT48012C. This tire has a radial ply construction which will be better for the longer highway trips you intended to make. It has a load range C rating…

view full answer...

Answer 9

On Curt brake controller #C24VV there is a 20 display so if the display is upside down is would look like 02 or 05. That message either indicates that a trailer is connected and the brakes are activated or, if it is flashing, that means it is in…

view full answer...

Answer 10

I was able to go out to the warehouse and measure the outer diameter of the hose on the #BH-3MFS-20 for you and found that it was .411 inches with a digital caliper like #PTW80157 which is just under 27/64ths of an inch.

view full answer...

Answer 11

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 12

When you use the Bearing Buddy Bearing Protectors like #BB2441, so you do not need to take apart the wheel hub and repack the bearings. The Bearing Buddy Protectors have a spring loaded seal that keeps the moisture and debris out of the bearings.…

view full answer...

Can Kodiak Disc Brake Kit Fit on Idler Hubs with Vault System

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching