Correct Lippert SolidStep for 24 Inch Wide Doorway

Question

Question:

My door frame measures 24-1/4 not sure wich one will work because what I read is I need at least 25 -1/2 ? Am I measuring correctly

asked by: Jeff B

0

Expert Reply:

You have measured correctly, and it looks like if you stretched out that tape measure so it was in a perfectly straight line your doorway would be 24 inches, but even if it was a hair over that it would not affect the fit at all.

Based on your 24 inch frame-to-frame measurement, you can use the SolidStep Manual Fold-Down Steps for 24" Wide RV Door Frames, so long as you have the following entry height:

- 22"-28" Entry Height: SolidStep Manual Fold-Down Steps for 24" Wide RV Door Frames - Double Step # LC713662

I have added a link to a video review for you to check out as well.

expert reply by: Kyle S

0

click to enlarge

Answer 1

The SolidStep Manual Fold-Down Steps for 24" Wide RV Door Frames - Double - Aluminum #LC713662 is roughly 22" wide when measured from the outside of each step frame, so you will be able to make this fit inside your 23-1/2" wide door…

view full answer...

Answer 2

In order to determine a suitable SolidStep Manual Fold-Down RV Step for a Forest River R-Pod Travel Trailer you'll first need to measure the doorway width (inner most point to inner most point) followed by the threshold height (ground to floor of…

view full answer...

Answer 3

Great question Rocky, so when the Lippert Solidstep part #LC713662 is folded up in the stored position it will take up 10 inches of space inside the doorway of your RV.

view full answer...

Answer 4

For such a low "entry height" you will actually need to use scissor steps such as #AS02 since there isn't a SolidStep option that will work. These scissor steps will work with an entry height of 18 to 23 inches. I have included a link…

view full answer...

Answer 5

I spoke with MORryde since the STP-017 is an OEM number and everything we offer is aftermarket and was found that that number should relate to the MORryde StepAbove RV Steps for 23-3/4" to 26-1/4" Wide Doorways #MR26RR. I would just measure…

view full answer...

Answer 6

The Lippert SolidSteps part #LC713662 that you referenced look like the picture that I attached.

view full answer...

Answer 7

In terms of choosing a Lippert Solid Step, you'll use the width of the finished door at it's narrowest. Round that number up to the next full inch, which in your case would be 28 inches. In that case, you'll want the adjustable model…

view full answer...

Answer 8

To replace your Iota IDP-240 you'll want to use the Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger #PD4560K18LS8. This panel is rated for 50 amp service, can provide both 120v/240v and is compatible with…

view full answer...

Answer 9

Since you'll have to factor the door thickness into the entry width you'll want to measure how far it sticks out while opened. The SolidStep Manual Fold-Down Steps for 24" Wide RV Door Frames #LC713662 are approximately 20 inches wide so…

view full answer...

Answer 10

The widest point of the Lippert #LC733932 Solid Step is 24 inches, which is the dimension from the outside of one stringer to the outside of the other. The latching mechanism that holds the steps folded upright into their storage position is width…

view full answer...

Answer 11

I'm assuming you're asking if you swap your Carrier unit to the Advent Air Replacement RV Air Conditioner for Carrier Setup #ACCAR150 will you still be able to use your current remote. If that's the case then yes you will absolutely be…

view full answer...

Answer 12

The bolt, or fastener screws, that come with the Replacement Hardware and Backer Plate for Lippert SolidStep Manual RV Steps #LC702580 are 10-24 x 4". This hardware is designed for Lippert SolidStep manual RV steps.

view full answer...