What is the Size and Length of the Replacement Hardware for Lippert SolidStep Fastener Screws

Question

Question:

Hello, Can you tell me the size and length of the bolts in this kit?

asked by: Robert J

0

Expert Reply:

The bolt, or fastener screws, that come with the Replacement Hardware and Backer Plate for Lippert SolidStep Manual RV Steps # LC702580 are 10-24 x 4". This hardware is designed for Lippert SolidStep manual RV steps.

expert reply by: Robin H

0

Answer 1

Yes, I verified with Lippert that the backer plate will fit the SolidStep 3.0 models with 24”, 26” and 30” widths; the correct part number is the following: - Replacement Hardware and Backer Plate for Lippert SolidStep Manual RV Steps #LC702580

view full answer...

Answer 2

The correct fitting fold down step that fits your 2019 Puma 19RLC is the Lippert StepAbove part #LC713662 which was designed for 24 inch wide doorways like you have and fits entry heights between 22 and 28 inches so your 26 inch measurement would…

view full answer...

Answer 3

The Replacement Leg for Lippert SolidStep 3- or 4-Step Manual Fold-Down Steps #LC96VR has an overall length of 25-1/2" and a length of 17" between the top hole to the bottom hole. It seems like you know. But just to clarify, this is a…

view full answer...

Answer 4

To install the Lippert SolidStep #LC791572 you will need to use two #10, 1-1/2 inch self-tapping screws (for a laminate floor) or two #10 - 1-1/2 inch wood screws (for a wood floor). After they are installed you will check the alignment and…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

On a 7-Way connector the suggested minimum wire gauge for the White (ground) wire, the Red or Black (power) wire, and the Blue (brake power) wire is 12 gauge. The minimum wire gauge for the remaining Green (right turn/brake) wire, the Yellow (left…

view full answer...