Does Class V Curt Trailer Hitch Receiver Fit 2006 GMC Sierra 3500

Question

Question:

2006 crew cab long bed duramax 3500 single wheel. Looking at this receiver for my truck. Will it fit Curt 15312 class v

asked by: Jacob

0

Expert Reply:

Yes, I can confirm for you that the class V Curt Trailer Hitch Receiver # C15312 is a fit for your 2006 GMC Sierra 3500.

This hitch has a 2" receiver and can tow up to 16,000 lbs with a tongue weight capacity of 2,400 lbs. I have added a link to the installation instructions for you to check out as well of the Curt Trailer Hitch Receiver # C15312.

expert reply by: Kyle S

0

Answer 1

The difference between the Curt Trailer Hitch Receivers #C15312 and #C15313 for your 2006 Chevrolet Silverado 3500 is that part #C15312 will work with vehicles that have the factory cutout bumper only while part #C15313 is designed to be used with…

view full answer...

Answer 2

The distance from the top of the mounting flange or bottom of the truck frame is to the top of the receiver tube on the Curt Trailer Hitch Receiver part #C15312 is 5-5/8".

view full answer...

Answer 3

Both of the Curt hitch receivers have the same bolt hole measurements. It's 9 inches from the first hole (Closest to the front of the truck) to the second hole and 5-1/2 inches from the second to the third. There's 39 inches across from hole…

view full answer...

Answer 4

I called my contact at Curt to confirm these measurements on the Curt #C15313 trailer hitch for you. The width of the hitch from center to center of the bolt holes measures 38-7/8 inches. The top of the receiver to the mounting holes measures 5-7/16…

view full answer...

Answer 5

All of the aftermarket trailer hitches that we carry for your 2011 Dodge Ram 1500 Bighorn state that they will not fit with a factory installed hitch, however, this typically refers to the factory hitches that hang below the rear bumper. I have heard…

view full answer...

Answer 6

I went and grabbed both hitches that you referenced to get the dimensions you asked about. If you check out all the attached pictures you will see the dimensions you are looking for the Curt #C14006 and #C15323.

view full answer...

Answer 7

34 inch frame hitch fits are for the cab and chassis model trucks. The part #C15312 does not fit cab and chassis model trucks so it would not be a fit for a 34 inch frame. The part #C15800 is an example of a Curt hitch that does fit a 34 inch wide…

view full answer...

Answer 8

The mounting holes the Curt Trailer Hitch Receiver #14053 measure 38-1/4" and 38-3/4" width-wise and then from the center of the of the forwardmost to the rearmost is 13-1/4". Attached is a dimensional photo for you to reference. This…

view full answer...

Answer 9

I went to the warehouse and measured the Curt Trailer Hitch Receiver, part #C15703. I have attached a photo of the trailer hitch and have noted the dimensions you can check out. This is a Class V trailer hitch and it has a 2-1/2 inch receiver…

view full answer...

Answer 10

I attached a picture that has basically every dimension of the Curt hitch part #C13161. It will hang down 8.28 inches from the mounting surface. From the rear mounting flange to the hitch opening it measures 15-3/4 inches.

view full answer...

Answer 11

According to my contact in the Tech Services department at Curt Manufacturing, the drop, or distance between the top of the mounting flange of the #14053 Class IV hitch and the top of the receiver tube is exactly 2 inches. You can see this in the…

view full answer...

Answer 12

The Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2" #14053 is a confirmed fit for the Ford Full Size Van but it is not a fit for a cab and chassis like you have which has a slightly wider frame. My recommendation due to the weight you…

view full answer...

Does Class V Curt Trailer Hitch Receiver Fit 2006 GMC Sierra 3500

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching