Recommended Trailer Hitch Receiver for 2000 Winnebago Itasca Spirit on Ford E-350 Chassis
Question:
Hi, I would like to buy a Class 4 hitch for my 2000 Winnebago Itasca Spirit 24 RV which is build on a Ford E350 Econoline Chassis, which has about 8000lb towing capacity with a few people on board. I plan to pull my 2015 Acura RDX 2WD on a tow dolly with surge brakes. Total weight is less than 6000lb, so Im assuming an 8000lb to 1000lb GTW should be ok. The frame extensions to the rear edge have bottom-side holes and are 39 inch apart, center-to-center. Im ok with some drilling, but in case it can be avoided, centered along each frame bottom there are 3 holes in a straight line, 1.5inch 5.5inch and 13.5inch from the rear edge of the frame. So, the spacing would be 4inch from first to second hole and 8inch from 2nd to 3rd hole center to center. It looks like CM-14053 would work - is this correct? Any other models to recommend, especially if they require less drilling? Much appreciated
asked by: Stephen K
Helpful Expert Reply:
The Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2" # 14053 is a confirmed fit for the Ford Full Size Van but it is not a fit for a cab and chassis like you have which has a slightly wider frame. My recommendation due to the weight you will be towing is to use the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2" # 41991-07. This is a weld on versus bolt on option, but all the bolt on options won't allow for the capacity you need.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 1000 lbs TW
- 10000 lbs GTW
- 12000 lbs WD GTW
- 2 Inch Hitch
- 1200 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Q&A: Mounting Hole Dimensions for the Curt Trailer Hitch Receiver # 14053
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2"
- Shop: Suspension Enhancement
- Shop: Vehicle Sway Bars
- Shop: Trailer Wiring
- Shop: Front Mount Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Drop of Curt Class IV Trailer Hitch # 14053
- Shop: Brake Controller
- Shop: Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2"
- Q&A: Distance From Frame to Receiver On Curt Trailer Hitch C15312 for Chevy Silverado
- Q&A: Dimensions of Curt Class V Trailer Hitch Receivers for 2007 Chevrolet Silverado
- Shop: TorkLift SuperHitch Magnum Trailer Hitch Receiver - Custom Fit - Class V - 2-1/2" and 2"
- Shop: Roadmaster Front Anti-Sway Bar - 1-3/8" Diameter
- Shop: Electric Heat Strip for Advent Air RV Air Conditioners - 5,500 BTU
- Q&A: Which Curt Trailer Hitch is a Fit for 34 inch Wide Trailer Frame
- Q&A: Trailer Hitch Option for a 2011 Ram 1500 Bighorn with OEM Hitch Under the Bumper
- Q&A: Dimensions and Hole Spacing for Brackets in Draw-Tite Service Body Trailer Hitch Receiver 41990-07
- Search Results: 2061
- Video: Curt Trailer Hitch Installation - 2003 Ford Van
- Shop: Mud Flaps
- Article: How to Choose the Right Trailer Hitch Class
- Video: etrailer RV Cargo Review - 2017 Thor Four Winds Motorhome