Availability of Angle Iron Bolts to Mount CE Smith Vertical Bunk Bracket

Question

Question:

Looking for two angle iron bolts. Do you have bolts that will work 3x2 galvanized angle iron? If I can get the bolts, also need two vertical pump brackets part number CE10603G. Thank you

asked by: James S

0

Expert Reply:

The only kind of mounting bolts we have for the CE Smith Light Duty, Vertical Bunk Bracket # CE10603G are square since that's what normally comes on boat trailers. The mounting slots are 4-3/8" long x 7/16" wide so if you can source the angle iron bolts elsewhere you'll want to make sure they don't exceed 7/16" diameter.

expert reply by: Jon G

0

Answer 1

I spoke with my contact at CE Smith about the Vertical bunk bracket, part #CE10604G. The outside width of the bracket is 2-1/16 inches and is designed to hold a 2 X 4 or a 2 X 6 board.

view full answer...

Answer 2

So the U-Bolt will secure the CE Smith Light Duty, Vertical Bunk Bracket #CE10603G with the ends pointing towards the back of the trailer. If you look at the picture you took it looks like those fasteners holding your current brackets could be…

view full answer...

Answer 3

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 4

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 5

The Kodiak Oil Cap #KPCAP you are looking at is a replacement cap for the Kodiak Pro Lube Kit. The oil cap you need is the Redline Oil Cap, Plug and O-Ring for Dexter 7-9K Trailer Axles #RG04-230. This will replace the oil cap on your trailer axles…

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

The best option for a Class C motorhome windsheild cover is going to be the Adco Deluxe Cover part #290-2507 which is designed for Class C motorhomes just like yours. I attached a review video for this cover for you to check out as well.

view full answer...

Answer 9

The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…

view full answer...

Answer 10

The closest match we have is the part #e54SR which is for a 3,500 lb axle and is 25-1/8 inches long. It would be a bit longer than what you have but it would work.

view full answer...

Answer 11

The adjustment holes on the Super Titan Forged Pintle Hook Plate part #RP38186 are 17/32" diameter so they will accept and are designed to be used with 1/2" bolts. It should not matter what brand pintle hook is used as the hole size and…

view full answer...

Answer 12

The Pintle Hook #C48215 that you referenced does include mounting hardware to attach to a pintle hook plate like the Super Titan Forged Pintle Hook Plate #RP38186 that you referenced. I also pulled these two parts and was able to determine that they…

view full answer...

Availability of Angle Iron Bolts to Mount CE Smith Vertical Bunk Bracket

Product Page this Question was Asked From

Continue Researching