Which Front Sway Bar Fits 2016 Tiffin Allegro 36LA

Question

Question:

I have a 2016 Tiffin Allegro 36LA on a 24,000 lb chassis. When I selected the Roadmaster 1139-148 font anti-sway bar it stated that not confirmed to fit but did show options for a bushing kit. Wondering why only the bushing kit will the other not fit?

asked by: Dale S

0

Expert Reply:

The correct front sway bar for your 2016 Tiffin Allegro with a 24k GVWR is the # RM-1139-148 that you referenced. I confirmed this with Roadmaster.

expert reply by: Jameson C

0

Answer 1

The Roadmaster Rear Anti-Sway Bar for Motorhomes #RM-1139-149 does not replace the stock sway bar, it will be mounted in addition to the stock bar.

view full answer...

Answer 2

You are right, removing the u bolt nuts is a very important step to the install the Roadmaster Rear Anti-Sway Bar #RM-1139-149. The size of the U bolts will determine what size the nuts holding them in place are. If they are 3/4" in diameter U…

view full answer...

Answer 3

Yes, the correct rear sway bar for your 2015 Thor motorhome built on a Ford F-53 22k chassis with a V10 is the part #RM-1139-149 that you mentioned. We confirmed this with Roadmaster. I also attached an install video for this for you to check out as…

view full answer...

Answer 4

We typically do not publish torque numbers because manufacturers have been known to substitute hardware of different hardnesses from time to time but they do a great job of keeping the installation instructions updated to reflect any changes.…

view full answer...

Answer 5

For your 2014 Tiffin Allegro 36LA that has a Ford F-53 Chassis with a V10 engine you would want the part #RM-RBK4-RSSA for a steering stabilizer by Roadmaster.

view full answer...

Answer 6

It looks like your 2011 Georgetown 350TS sits on the Ford F53 chassis. (20,500 GVWR) Many F53 Users report sway in the ride. Yes, I would get the Roadmaster #RM-RBK22-RSSA Steering Stabliliser with mounting brackets. Next I would adding the…

view full answer...

Answer 7

Stabilizers are designed to dampen side-to-side movement of the wheels while sway bars are designed to reduce body roll during fast cornering and since RVs tend to sway side to side when traveling adding in anti-sway bars like the Roadmaster Front…

view full answer...

Answer 8

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...