Pivoting of Head on Curt E16 5th Wheel Head

Question

Question:

Does the head pivot side to side at all or is it fixed.

asked by: Al P

0

Expert Reply:

The Curt E16 5th Wheel Trailer Hitch w/ R16 Roller - Slide Bar Jaw - 16,000 lbs # 16516 will pivot side to side and front to back. This allows you to connect and disconnect on slightly unlevel ground. I've attached a couple videos to assist with the visual.

expert reply by: Jason S

0

Answer 1

Hey there Mike; good question and the answer is yes it does. The Curt E16 hitch you asked about does fit with those exact base rails in your 2017 Ram 1500 short bed. You have the exact part numbers correct for your truck as well: - Curt E16 5th Wheel…

view full answer...

Answer 2

Yes, your Reese 5th wheel trailer hitch, #RP30047, will fit the Curt above the bed rails in installation kit #C16426-204. The rails will accept Curt, Draw-Tite, Hidden Hitch, Husky, Reese, and Valley hitches that fit in above the bed rails. And the…

view full answer...

Answer 3

No, The Curt Custom Fifth Wheel Installation Kit for Ram Truck #C16427-104 will not fit your 2013 Ram 1500. You will need The Curt Custom Fifth Wheel Installation Kit #C16444-204. These custom brackets mount beneath your truck bed to provide…

view full answer...

Answer 4

On beds shorter than 6 feet you will need a fixed hitch and a Sidewinder on the trailer to be able to make tight turns. For a 5th wheel trailer hitch installation kit you can use kit #RP30035-386. For a hitch, if 16,000 pounds is enough for the…

view full answer...

Answer 5

Since you will be towing, what you will need for your Keystone Cougar 318SAB is a frame-mounted RV hitch, and that is simply going to depend on the width of your trailer frame (the width is measured from inside to inside). After you measure (or if…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 11

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 12

Beds shorter than 8 foot do commonly need a slider hitch David, but a lot of modern fifth wheel trailers are now made with tapered noses to help and in a lot of cases a slider isn't required. So if the trailer you plan to tow has a tapered nose…

view full answer...

Pivoting of Head on Curt E16 5th Wheel Head

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching