Drilling Holes for Installation of the Fulton Fold-Away Coupler Hinge # FHDPB330301

Question

Question:

Is there an approach to drilling the bottom holes on the trailer side of the folding coupler. It seems to me one would be drilling pretty much blindly from the bottom? I was not intending on removing the boat for this installation.

asked by: Jim D

0

Expert Reply:

Once you have the trailer tongue cut and you place on the hinge, # FHDPB330301, put the other end of the tongue in place on the open end. Once everything is in position you can mark the holes or use the hinge as a template and drill the holes. Using the hinge as a template would take the guess work out.

expert reply by: Michael H

0

Answer 1

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 2

The bolt running down the middle of your leaf springs will keep them together, but if they are showing as much rust as you said they are it would be a good time to replace your springs. The clips are designed to help keep the leafs together although…

view full answer...

Answer 3

Two 12 foot long bunks boards will work well to support your 21 foot boat. Ideally, the bunk boards should be at least half as long as your boat and run from the stern (or a few inches beyond it) to the bow as far forward as you like. Due to shipping…

view full answer...

Answer 4

Thanks for the photo. It does indeed look like you need to move your keel rollers up towards the bottom of the boat until they are touching but not supporting the full weight. Therefore, marking the bracket when the rollers are flush to the bottom…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...