Easy to Install 4-Way Trailer Wiring Recommendation for 2007 Ford Ranger

Question

Question:

When owned a 1997 Ford Ranger purchased a T style wire harness adapter that fit into OEM wire harness for trailer wiring. I am trying to locate same item for my 2007 Ranger ,if available where can purchase. Thank you for your assistance

asked by: Tom

0

Expert Reply:

We have just what you are looking for with the Hopkins trailer wiring kit part # HM40655 which easily plugs inline with the taillight connectors at the rear of your 2007 Ford Ranger.

expert reply by: Jameson C

0

Answer 1

Installing the Curt T-Connector Vehicle Wiring Harness item #C55515 will not require you to flash the ecu on your 2007 Ford Ranger. This harness installs on the Ford Ranger's with the factory tow package. If your truck didn't come with a…

view full answer...

Answer 2

I confirmed with Curt that the total length of the Curt T-Connector Vehicle Harness, Item #C55515, is 37 inches from end to end. It will plug directly into your OEM tow package port with no splicing required. Let me know if you have any other…

view full answer...

Answer 3

The Hopkins Plug-In Simple Vehicle 4-Pole Wiring Harness #HM40655 is intended for vehicles without any factory tow package wiring, although it could still be installed in a truck that does have this feature. This item installs by plugging in to the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Easy to Install 4-Way Trailer Wiring Recommendation for 2007 Ford Ranger

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching