Adapter to Connect 1/4 inch Brake Line to Hydrastar Electric Over Hydraulic Brake Actuator
Question:
I am trying to make the final connections in my new brake system on my tri-axle boat trailer. I have the Hydrastar HBA16 electric over hydraulic actuator, and Kodiak disc brake kit K2HR526DS x2 all purchased on etrailer. I am using 1/4inch stainless steel brake line to make the runs from the actuator to the brakes. Can you tell me what the thread count/pitch on this part #HS43-9035 is. I believe I need this to make the connection to the Hydrastar however I am still trying to track down these additional fittings: 1 male flare fitting to connect 1/4inch brake line to HS43-9035, 3 1/4inch tee connections, one for T off at front of trailer to run a stainless line down each I-beam not necessary but how I want it done, two for T off at each front axle with a brake hose connecting to each front caliper brake hose also needed. Then I need two additional 1/4inch connections for the stainless lines and two additional brake hoses to make the connection at the second axle brake calipers. Are you able to help with these ions? Thank you,
asked by: Thomas M
Expert Reply:
The adapter part # HS43-9035 that you referenced is an adapter that plugs into the back of the HydraStar Actuators like the part # HBA16 that you have to go from 3/16 inch line size to 1/4 inch like you have now.
We don't have the 1/4 inch tee fittings you are looking for oddly enough.
Products Referenced in This Question
Hydrastar Electric Over Hydraulic Actuator for Disc Brakes - 1,600 psi
- Brake Actuator
- Electric-Hydraulic Brake Actuator
- 1600 psi
- Disc Brakes
- Hydrastar
more information >
Product Page this Question was Asked From
Brake Line Fitting for Hydrastar Hydraulic Brake Actuators - 1/4"
- Accessories and Parts
- Brake Actuator
- Trailer Brakes
- Hydraulic Drum Brakes
- Brake Lines
- Brake Line Fitting
- Brake Line Components
- Hydrastar
more information >
Continue Researching
- Shop: Replacement Orifice Connector for Dexter Actuators
- Shop: Brake Line Fitting for Hydrastar Hydraulic Brake Actuators - 1/4"
- Q&A: Master Cylinder Brake Line Fitting for Titan Model 60 Disc Brake Actuator
- Shop: Dexter Hydraulic Brake Line with Fittings - 13" Long
- Shop: Replacement Master Cylinder and Push Rod Assembly for Drum Brakes - Model 10 and 20 Actuators
- Shop: Replacement Solenoid Adapter Fitting for Dexter Model 10 Brake Actuators Made Before 2010
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Video: Tekonsha Push-To-Test Trailer Breakaway Kit Installation
- Video: Hydrastar Trailer Brakes HS43-9035 Review
- Shop: Replacement Master Cylinder Assembly for Dexter Model 10 and Model 20 Brake Actuators - Disc
- Search Results: brake line fittings
- Video: Hydrastar Trailer Brakes HS641-3307 Review
- Video: Review of Titan Brake Actuator - Replacement Master Cylinder for Disc Brakes - T4747100
- Q&A: Is Brass Metering Adapter Needed w/Replacement Master Cylinder for Model 10/20 Disc Brakes
- Shop: Trailer Hitch
- Video: Choosing the Right Trailer Wiring
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Search Results: 44649
- Article: Trailer Wiring Diagrams
- Search Results: 68149
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Trailer Wiring
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Video: Choosing the Right Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 25580
- Q&A: Trailer Suspension Hanger Kit for Slipper Springs and 38 inch Wheelbase
- Shop: Fifth Wheel Hitch
- Search Results: dust cap
- Video: Roadmaster Automatic Battery Disconnect Installation - 2020 GMC Sierra 1500