Recommended Rack for Fiberglass Tonneau Cover

Question

Question:

I am searching for a roof rack to add to the topside of a fiberglass tonneau cover.

asked by: Geoff K

0

Expert Reply:

In order to install a rack on top of a fiberglass tonneau cover you can use the Rhino-Rack # Y02-480B which comes with everything that you need including the adjustable tracks which allow you to get the exact crossbar spread you need.

expert reply by: Conner L

0

Answer 1

Based on your bed length and camper shell type the Rhino Rack Camper Shell Roof Rack setup part #Y02-480B would work but there's a chance you might need to trim down the tracks as they are right at 5-1/4 feet in length. There is no difference…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

The Rhino-Rack Heavy-Duty Roof Rack Roof Rack have specific C-channels that are designed to fit specific Rhino-Rack Heavy-Duty accessories, like the Rhino-Rack Hi-Lift Jack and Shovel-Holder Brackets #RRRCB-RSHB-RJHB as an example. That's the…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your canopy. Per…

view full answer...

Answer 7

The Rhino-Rack Aero Bar Roof Rack for Camper Shells part #Y02-480B is a great option for fiberglass truck bed campers as it was made for this exact purpose. It can support up to 220 lbs but bear in mind this rating is tested independently of the…

view full answer...

Answer 8

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 9

The Rhino-Rack Roof Rack for Factory Tracks #Y02-490B-NT is going to be your best bet for the tracks on the ARE topper for your 2012 Toyota Tacoma. The weight capacity is 220 lbs like you mentioned, but that's going to be the highest you'll…

view full answer...

Answer 10

Thanks for reaching out to verify, Frank! Yes, those parts (listed below) will fit great together and on your 2010 Honda Accord Crosstour with the naked roof. Inno Roof Rack - Aero Crossbars #INXB130-138 - Through Feet #INXS250 - Fit Kit #INK587 The…

view full answer...

Answer 11

Yes. You will need to use everything included with the Rhino-Rack Roof Rack for Thule and Yakima Tracks - 2 Heavy-Duty Crossbars - Black - 65" #Y01-140B-NT to install into the tracks you have pictured. The bases of the legs mount right into the…

view full answer...

Answer 12

Yes, the Roamer LT Roof Rack for Pop-Up Campers and Camper Shells #S80510 will fit your 2023 Forest River Flagstaff 176LTD. It is also what I recommend to add a roof rack for a bicycle carrier on your camper. Once installed you will be able to add…

view full answer...

Recommended Rack for Fiberglass Tonneau Cover

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching