How does the Small Edge Trim Install

Question

Question:

I am interested in buying this product, I also need the channel it slips into. Can you please let me know which channel piece to buy also, thanks

asked by: Chris P

0

Expert Reply:

The Small Edge Trim for Enclosed Trailer part # 362ET4119-25 slides over the sharp edge you're trying to cover. If you look at the video I've linked you can see that the trim has an opening for the edge being covered to slide into. It is a soft and malleable material that is compressible and does a great job protecting things that may come in contact or for sealing up gaps is doors or compartments.

expert reply by: Randy B

0

Answer 1

I have another option for you, but the Camco RV Vinyl Trim Insert #CAM25202 is not for windows, entry doors, compartment doors, or vents. We have a few window weather strips available which I have listed below so you can see what size works for you.…

view full answer...

Answer 2

My contact at Redline told me that the outside diameter of the Chrome Trim #SA1012ET would be right at 5/16 of an inch and the inner diameter 1/8 of an inch. He said the trim isn't a perfect circle so the dimensions fluctuate a little bit.…

view full answer...

Answer 3

The Chrome Edge Trim #SAT012ET can fit metal thicknesses up to 1/8 of an inch. It doesn't have a minimum thickness stated. Basically anything you'll have on the exterior of an RV with less than 1/8 of an inch is going to work.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

How does the Small Edge Trim Install

Product Page this Question was Asked From

Continue Researching