CE Smith CE27610 Guide-On Rollers For 14 Foot Lowe Sea Nymph Fishing Boat

Question

Question:

Hi, I have the 2005 Lowe 14foot Sea Nymph V 1467 WT with an EZ loader trailer which uses bunk style guide on. Fishing the snake it gets so windy at times the last time fishing trying to get the boat on the trailer it broke the bunk. Would this roller guide on be a good replacement for the bunk style or is there another recommendation? thanks

asked by: Jerry A

1

Helpful Expert Reply:

The # CE27610 CE Smith Roller Guide-Ons for Boat Trailers would be absolutely perfect for your application. The rollers will do a great job of redirecting the bow of your boat when you're trying to load up the boat on the trailer in less than ideal conditions. The guide-ons will fit trailer frame members up to 3 wide x 4-1/4 inches tall, right out of the box, or for frame members that are up to 3 wide x 5-1/4 inches tall, 2 of the extended length U-bolt kits would be needed, part # CE11416.

I've linked to a product description video featuring the guide-on rollers.

expert reply by: Mike L

1

click to enlarge

Answer 1

The CE Smith Replacement Hardware for Post-Style Guide-Ons #CE11452-A consists of 3-1/2 x 5-inch long U-bolts and brackets that measure 4-5/8 x 3-7/8 inches, according to my contact at CE Smith. This hardware kit is intended for replacing parts from…

view full answer...

Answer 2

The inside width of the CE Smith Extra-Long U-Bolts #CE11416 is 3-1/4-inches so that they can fit trailer frames up to 3-inches wide x 5-1/4-inches tall.

view full answer...

Answer 3

Sounds like you are referring to guide on rollers like the CE Smith Roller-Style Guide-Ons for Boat Trailers #CE27610. These mount at the rear of the trailer frame and act as a guide to allow the boat to slide on as easy as possible. I attached a…

view full answer...

Answer 4

You will want the boat to be close to touching the rollers on the CE Smith Roller-Style Guide-Ons #CE27610. Since the guide-ons are not meant to support weight you will want to place them so that they are fairly close to the boat but not too far.…

view full answer...

Answer 5

It's perfectly okay if the entire roller of the CE Smith Roller-Style Guide-Ons #CE27610 does not touch the side of the boat. 1/2 inch of clearance on either side between the boat hull and the rollers would be a great amount of clearance.

view full answer...

Answer 6

When installing guide-ons on your boat trailer, like part #CE27636, you want to make sure that they extend high enough that they are easily visible when you are loading your boat. If you feel comfortable loading your boat with the guide-ons being…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

CE Smith CE27610 Guide-On Rollers For 14 Foot Lowe Sea Nymph Fishing Boat

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching