Inside Width Dimension of CE Smith Extra-Long U-Bolt Kit CE11416

Question

Question:

What is the inside width of the Ubolts?

asked by: Dave

0

Expert Reply:

The inside width of the CE Smith Extra-Long U-Bolts # CE11416 is 3-1/4-inches so that they can fit trailer frames up to 3-inches wide x 5-1/4-inches tall.

expert reply by: Adam R

0

Answer 1

The #CE27610 CE Smith Roller Guide-Ons for Boat Trailers would be absolutely perfect for your application. The rollers will do a great job of redirecting the bow of your boat when you're trying to load up the boat on the trailer in less…

view full answer...

Answer 2

The CE Smith Replacement Hardware for Post-Style Guide-Ons #CE11452-A consists of 3-1/2 x 5-inch long U-bolts and brackets that measure 4-5/8 x 3-7/8 inches, according to my contact at CE Smith. This hardware kit is intended for replacing parts…

view full answer...

Answer 3

You'd really need to base it off the hull design of the boat you plan to tow. I'd use swivel bunk brackets like the part #CE10000G-4 to mount the boards as these allow you to angle the boards to match the shape of your boat's…

view full answer...

Answer 4

The CE Smith Bolster and Swivel Bracket Assemblies #CE10000G-4 do have a galvanized finish for superior rust resistance but they are meant to be installed on boat trailers and not really meant to stay submerged for extended periods of time. Although…

view full answer...

Answer 5

The CE Smith Bolster and Swivel Bracket Assemblies part #CE10000G-4 do not have a specified weight capacity as it can vary by the strength of the u-bolts used in conjunctions with these brackets as well as how many brackets are used per board. I know…

view full answer...

Answer 6

The mounting bracket of the CE Smith Bolster and Swivel Mounting Brackets, #CE10000G-4, are bent at a 90 degree angle. The photo of the 4 brackets can be somewhat deceiving, but I grabbed one from our warehouse and made a short video for you so you…

view full answer...

Answer 7

I assume you have either the Firestone Ride-Rite Air Helper Springs part #F2299 or the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs part #F2701 on your 2006 Dodge Ram 3500. If that is the case then you will want to use the…

view full answer...

Answer 8

I went out to the warehouse and pulled replacement u-bolt #853-3105 to take some measurements. The width between the two ends is approximately 2-7/16 inches. The center to center distance though is 2-11/16 inches. The internal length is 3-1/2 inches…

view full answer...

Answer 9

I assume you have either the Firestone Ride-Rite Air Helper Springs part #F2299 or the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs part #F2701 on your 2006 Dodge Ram 3500. If that is the case then you will want to use the…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Inside Width Dimension of CE Smith Extra-Long U-Bolt Kit CE11416

Product Page this Question was Asked From

Continue Researching