What Size Wheel Studs Fit Through Trailer Wheel # AM20758

Question

Question:

I know this wheel is made for 1/2inch wheel studs but Im wondering what the actual lug bolt hole size in the wheel is. Also does it us the standard 60° conical lug seat? Thank you for your help.

asked by: Bob

0

Expert Reply:

The wheel bolt hole diameters of the # AM20758 is just slightly over 1/2 inch which allows only 1/2 inch wheel studs to fit through. You wouldn't be able to fit a 9/16 inch or larger stud through the hole. The lug nuts to be used with this wheel do have the 60 degree cone shape like the part # AM90049.

expert reply by: Jameson C

0

Answer 1

For your existing 15" x 5" wheels an ST205/75R15 trailer tire size will work perfectly (an ST225/75R15 like what you were looking at will be a bit too wide). Within this size I specifically recommend the Taskmaster Provider #TR20515D. It…

view full answer...

Answer 2

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 3

The Aluminum Sendel Series T07 Black Machined Trailer Wheel #AM97XR does not require longer wheel studs and would work with what you have currently. These wheels were designed to fit standard wheel stud lengths like what your trailer has currently.

view full answer...

Answer 4

My favorite aluminum trailer wheel we offer that matches the criteria you mentioned is the Aluminum Liger Trailer Wheel - 15" x 5" - 5 on 4-1/2 - Gunmetal Gray #LH35FR. This is a 15 inch diameter by 5 inch wide wheel with a 5 on 4-1/2 inch…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 9

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...