Correct Oil Seal for Dexter 10K 8-214-5UC1 Hub/9-27 Brake Drum

Question

Question:

Will the 10-63 seal work on my 10,000 lb dexter axles with 9-27 hubs?

asked by: Nathan J

0

Expert Reply:

The 9-27 (it's 9-27-1, actually) brake drum is part of a 2 piece hub/drum that uses # 8-214-5UC1 for the oil bath hub assembly. The correct oil seal is part # 10-56. The seal has an OD of 4.5 inches, and an ID of 3.125 inches. The # 10-63 you'd mentioned is too small, as its typically used with 8K capacity axles, so it wouldn't be compatible.

expert reply by: Mike L

0

Answer 1

The Unitized Oil Seal #10-51 would require that you apply RTV like part #LT37464 to the outer diameter of the seal before you install it per Dexter's seal installation instructions. This seal is designed as a replacement for Dexter 9K and 10K…

view full answer...

Answer 2

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

Hey Jason, I spoke with Furrion and they stated that the Furrion Chill Cube is OEM only currently and should be released to the aftermarket distributors later on this year (2024), but there is no solid date. That says to me that they're probably…

view full answer...

Answer 9

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 10

Hey Jon, Yes, the Advent Air Low Profile RV Air Conditioner #ADV79FR is compatible with the Air Distribution Box #ACDB. This would have the controls on the air distribution box instead of a wall mounted thermostat. We don't currently have any…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Jonathan, We haven't heard of any issues with the P3 #90195 and plug-in harness #3070-P with a 2024 Honda Ridgeline. How are you sure that the brakes are being applied on your Honda when applying the manual override on the P3? What are you…

view full answer...

Correct Oil Seal for Dexter 10K 8-214-5UC1 Hub/9-27 Brake Drum

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching