Will the Thule Hullavator Work With the Malone AirFlow2 Roof Rack On a 2015 Chevy Equinox

Question

Question:

I have a 2015 chevy equinox, can I use the Malone AirFlow2 Roof Rack - Aero Crossbars - Raised, Factory Side Rails - Aluminum - 58inch Long, part# MPG216 to mount the thule hullavator, part#TH898 onto? Also how do I lock the hullavator, I cant seem to find the locks which are not included with it

asked by: Jody N

0

Expert Reply:

Yes, you can mount the Malone AirFlow2 Roof Rack part # MPG216 on a 2015 Chevrolet Equinox to use the Thule Hullavator Pro Kayak Carrier part # TH898. In order to lock the Thule Hullavator, you need the Thule One-Key System Lock Cylinders part # TH450200. There are plugs in the housing that the lock cores install in that will need to be first removed.

expert reply by: Conner L

0

Answer 1

The Thule Hullavator Pro Kayak Carrier #TH898 can certainly be installed onto a roof rack that is not Thule brand. To determine what size crossbars you need, you will want to measure from the center of one roof rail to the center of the next roof…

view full answer...

Answer 2

For your 2020 Nissan Rogue the roof rack you'd need to mount the Thule Hullavator #TH898 on the Thule Wingbar roof rack part numbers #TH711200 and #TH710401. This rack has the overhang needed for the Hullavator to attach to and has top channels…

view full answer...

Answer 3

The Thule #TH898 Hullavator would be compatible with the 1-1/4 x 7/8 inch crossbars provided by the Malone #MPG202 roof rack. However, in order for the Hullavator to operate properly, the crossbars will need to extend at least 4 inches past the roof…

view full answer...

Answer 4

For your 2013 Toyota Sequoia with Hullavator #TH898 to have a quieter system, I recommend the Evo Raised Rail Feet for Thule Crossbars #TH710401 along with the Thule WingBar Evo Crossbars - Aluminum - Black - 60" Long #TH711520.

view full answer...

Answer 5

If you have the current version of the Thule Hullavator like what you referenced part #TH898 it comes with the needed hardware to install into the top crossbar channels of the bars you sent in a picture of. We have them as a replacement part…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

You could leave off installing the outside wheel clamp of the RockyMounts WestSlope bike rack part #RKY10222 but you can't shorten the frame of the rack where the wheel mounts are. For a bike rack with a smaller footprint that can carry up to two…

view full answer...