How does the Optronics LED Identification Light # MCL98RB Mount

Question

Question:

how does this lamp mount?

asked by: James

0

Expert Reply:

The Optronics LED Identification Light, # MCL98RB, is a surface mount light that has two holes for mounting screws. The mounting holes measure 3/16 inch x 3/8 inch and are 8-1/2 inches apart on center. I have attached a photo showing the dimensions for you.

The mounting hardware is not included with the light, but any local hardware store will carry the necessary screws.

expert reply by: John H

0

click to enlarge

Answer 1

I recommend the LED Combination Trailer Tail Light #STL57RB and #STL56RB. The lights are 6-1/16" long x 3-5/8" tall x 2-1/4" deep and have mounting holes that are 2" on center. They are sealed lights that are submersible and…

view full answer...

Answer 2

I wasn't able to find anything based on the part number you listed. Do you happen to have a picture of the light cluster? A lot of times with that I can find what you'd need.

view full answer...

Answer 3

For your 2013 Ford F-150, the SumoSprings that are the best option for you while you are towing are the 1,000 lb capacity springs: - SumoSprings Solo Custom Helper Springs #SSR-117-40 These are the blue springs (I verified with SumoSprings there…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

How does the Optronics LED Identification Light # MCL98RB Mount

Product Page this Question was Asked From

Continue Researching