Replacement Motor and Fan Blade For Ventline V2094 Exhaust System

Question

Question:

I have a 2014 26ft BH Avenger camper by Prime Time MFG. I have a ventline v2094 exhaust system in bathroom and need replacement motor and fan blade that is 12v and 1.2amp. Will the BVD0218-00 and the BVD0215-00 work for mine?

asked by: Shane

1

Helpful Expert Reply:

Yes, the replacement motor you need for your V2094 Vent is the part # BVD0218-00. The replacement fan blade is part # BVD0215-00 as well.

expert reply by: Heather A

1

Answer 1

The correct replacement motor you would need for your V2094 Vent is the part #BVD0218-00. It sounds like you have the older version of this vent so you would also need to upgrade the fan blade as well with part #BVD0215-00.

view full answer...

Answer 2

I have a few things for you to check when it comes to not being able to pair your iPhone with the Curt Echo #C51180. The first thing to do is make sure that you're pairing your phone with the Echo through the app. If you paired it through…

view full answer...

Answer 3

You can easily replace the thermostatically controlled RV ceiling fan you have in your 1999 Holiday Rambler Endeavor 37WDS with one that does not have that feature. We have the Ventline Ventadome Trailer Roof Vent part #V2094SP-28 which fits the…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 6

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 7

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Replacement Motor and Fan Blade For Ventline V2094 Exhaust System

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching