How Thick is the Metal on the Hooks of the Gen-Y Hitch Aluminum Loading Ramps

Question

Question:

What is the thickness in inches of the hooked ends that attach to trailer deck?

asked by: Howard B

1

Helpful Expert Reply:

The hooked ends of the Gen-Y Hitch Aluminum Loading Ramps # GH34FR are going to be 3/8" thick. This ramp set will hold up to 8000-lbs total (4000-lbs per ramp) and are 14 feet long to provide a long angle of approach that is perfect for large, heavy equipment.

expert reply by: Erik B

1

Answer 1

Sorry for any confusion, the angle cut on the Gen-Y Hitch Aluminum Loading Ramp Set #GH34FR is on the top of the ramp like you are wanting. The bottom cut version is for the shorter ramps. The top cut is over 18 inches long though so it's not an…

view full answer...

Answer 2

That is correct. If your 2021 Wrangler Unlimited has the connector located under the dash to the left of the steering column near the top of the e-brake pedal as shown in the provided photo, you'd use the #3073-P harness to connect the #90195…

view full answer...

Answer 3

We have a very good solution for your problem! With the factory tow package you can use Tekonsha Custom Wiring Adapter for Trailer Brake Controllers - Jeep part #3073-P this custom adapter allows you to plug in directly to the existing port under…

view full answer...

Answer 4

The wiring color codes and wire gauge recommendations for the Pollak Heavy-Duty, 7-Pole, Round Pin, Trailer Wiring Connector, item #PK11700, are listed below. White - Ground Return - 8 gauge Black - Clearance, Side Marker, Identification - 12 gauge…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hi Tony, thanks for writing in and yes, we can 100% get your 2023 Jeep Wrangler set up to be flat towed behind your Holiday Rambler motorhome. To make it easy to order I'll go ahead and list everything out for you. - Base Plate Kit: Roadmaster…

view full answer...

Answer 11

Yes, the Brass Tire Sensors for TireMinder TPMS #TM-2Brass would fit and work on the valve stems of your 2023 Jeep Wrangler.

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

How Thick is the Metal on the Hooks of the Gen-Y Hitch Aluminum Loading Ramps

Product Page this Question was Asked From

Continue Researching