What is Difference Between Hitch Pin Diameters of 1-1/4 inch and 2 inch Hitches

Question

Question:

are you using a 1/2 diameter pin into the 5/8 hole for clearance

asked by: Charles G

0

Expert Reply:

The Curt Class I and II Pin and Clip # C21410 is designed for use on 1-1/4 inch trailer hitches which do have 1/2 inch diameter hitch pin holes. The larger 5/8 inch hitch pins are used on the larger 2 inch hitch size. For that we have the part # C21510.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The first thing I would check is the trailer wiring running light fuse located in the power distribution box under the hood. Once the fuse box is located check the legend on the lid to determine the correct fuse to check. Blown running light fuses…

view full answer...

Answer 4

The hitches made for your 2014 Fiat 500L are the light-duty Class I type and in one of these you will need to use a Class I-compatible hitch-mount cargo carrier. One thing to keep in mind is that the combined weight of your chosen carrier and what…

view full answer...

Answer 5

To replace the factory hitch on your 2002 Ford E-350 Super Duty Van you can use the Draw-Tite Ultra Frame #41945 which has the bolt holes 38-5/8" apart (center on center). This hitch will be the perfect replacement for your factory hitch.…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

The only bike rack that you can add onto that is like the Kuat Sherpa #SH22G is the Kuat NV #BA22B by using this add on #BA02B.

view full answer...

Answer 8

While we do have a great lightweight cargo carrier that fits your 1-1/4" hitch on your 2014 Subaru Forester, the only aluminum ones we carry are designed only to fit 2" hitch receivers. The manufacturers unfortunately discontinued…

view full answer...

Answer 9

Yes, you can install the Firestone Ride-Rite Air Helper Springs #F2613 on your 2022 Chevrolet Silverado 2500HD with the Curt Q20 5th Wheel Trailer Hitch #C16130. The Curt Custom Fifth Wheel Installation Kit #C16429-204 will use different mounting…

view full answer...

Answer 10

To hook up a trailer jack to a 12 volt battery you need to make the connection from the jack's power wire to the positve post on the battery using a ring terminal, like part #DW05705-1. If you don't already have a battery on the trailer you…

view full answer...

Answer 11

For a 3500 lb Electric Jack, I recommend the Bulldog Powered-Drive Trailer Jack - Drop Leg - A-Frame - 14" Lift - 3,500 lbs - Black #BD500187. This jack uses a 12 volt system, so it is compatible with your 7-way although a battery is always a…

view full answer...

Answer 12

The Electric A-Frame Tongue Jack, #JET-3555, runs off a 12 volt battery. The best source for power would be from a 12 volt battery (like a car battery) mounted on the trailer. The red power wire on the Electric A-Frame Tongue Jack, #JET-3500, is the…

view full answer...

What is Difference Between Hitch Pin Diameters of 1-1/4 inch and 2 inch Hitches

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching