Height of Timbren SES Kit, # TGMRTT35D and Recommended Clearance Between Frame and Axle
Question:
Im looking to install this on my 2012 sierra 2500. I have a 6inch lift installed on my truck and was wondering the product height, so i can figure out how many spacers i will need... and if theres a limit to how many spacers can be used?
asked by: Nick
Expert Reply:
The single convoluted springs from the Timbren SES Kit # TGMRTT35D are only 3-9/16 inches tall, but this kit also includes a 1 inch spacer, so it will sit 4-9/16 inches below the jounce bumper holder on the frame. Timbren recommends a distance of 1 inch between the Timbren and the vehicle so you'd need a spacer setup based on what dimension you have now minus 5-9/16 inches.
You can achieve this distance on trucks that are lifted using increments of the Timbren 1/2" Spacer part # TA25722-90P00 and the Timbren 1" Spacer part # A25723-90AH00 until the 1" of space is acquired.
Products Referenced in This Question
Timbren 1" Spacer For Raised Frame Vehicles - 3/8" Bushing
- Accessories and Parts
- Vehicle Suspension
- Spacers
- Timbren
more information >
Timbren 1/2" Spacer for Raised Frame Vehicles
- Accessories and Parts
- Vehicle Suspension
- Spacers
- Lift Spacers
- Timbren
more information >
Product Page this Question was Asked From
Timbren Suspension Enhancement System - Severe Service - Rear Axle
- Vehicle Suspension
- Rear Axle Suspension Enhancement
- Jounce-Style Springs
- Extra Heavy Duty
- Timbren
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Suspension Enhancement
- Shop: Timbren Suspension Enhancement System - Severe Service - Rear Axle
- Video: Timbren Vehicle Suspension - Rear Axle Suspension Enhancement - TGMRTT35D Review
- Shop: Timbren Rear Suspension Enhancement System
- Shop: Vehicle Air Mattress
- Video: Timbren Rear Suspension System Installation - 2022 Chevrolet Silverado 3500
- Video: Timbren Rear Suspension System Review
- Video: Timbren Rear Suspension Enhancement System Installation - 2020 GMC Sierra 2500
- Video: Timbren Rear Suspension System Installation - 2015 Chevrolet Silverado 3500
- Q&A: Comparing Timbren TGMRCK25D or TGMRTT35D Rear Axle Jounce Springs for 2015 Silverado 2500
- Q&A: Comparing Timbren Helper Springs for a 2015 Chevy Silverado 3500
- Q&A: What Holds the Rubber Springs in Place on the Timbren Kit # TGMRCK25D on a 2012 Chevy Duramax
- Q&A: Will The Curt Hitch # C13206 on My 2019 Subaru Outback Wagon Fit On My 2022 Subaru Outback Wagon
- Q&A: Will The Timbren Suspension Enhancement System Fit A 2022 GMC Sierra 3500?
- Q&A: Best Way to Prevent Sagging Suspension When Towing a Trailer
- Q&A: Are Timbren Jounce Springs Good For Use When Hitch Towing On 2023 GMC Sierra 2500?
- Shop: SumoSprings Rebel Custom Helper Springs - 2 Piece - Rear Axle
- Shop: Front Mount Hitch
- Search Results: torklift
- Shop: Spacer Kit for Timbren Suspension Enhancement System
- Shop: 24x27 TorkLift Lock and Load Maximum Security Cargo Tray for 2" Hitches 500 lbs
- Shop: SumoSprings Solo Custom Helper Springs - Rear Axle
- Shop: Trim Kits
- Shop: Floor Mats
- Search Results: propane detector
- Video: Review of Go Power Portable Chargers - Power Banks - Solar Panels - GP22RR
- Shop: RV Propane Gas and Carbon Monoxide Detector - 12 Volt - 2 Wire - Black
- Search Results: torklift fastgun locks
- Search Results: hitch receiver plug
- Video: SuperSprings Vehicle Suspension - Rear Axle Suspension Enhancement - SSR-207-47 Review