Yakima HullRaiser to HullRaiser Aero Conversion Kit on a Subaru Tribeca

Question

Question:

? have a subaru tribeca with factory rack will this fit and is this a yakima product or aftermarket? thanks

asked by: Tom

0

Expert Reply:

The Yakima HullRaiser to HullRaiser Aero Conversion Kit, Y8860031, is a Yakima product. The conversion will fit virtually all base rack cross bars, including factory cross bars. If you do not have crossbars going across your vehicle from driver side to passenger side on your factory rack, then you will need to get those.

expert reply by: Robert G

0

Answer 1

I attached a picture that has shows the installation instructions for the Yakima HullRaiser to HullRaiser Aero Conversion Kit #Y8860031. This will show you how to convert your Hullraiser to work on Aero bars. You'll also need the part #Y8890057…

view full answer...

Answer 2

I attached a picture that has shows the installation instructions for the Yakima HullRaiser to HullRaiser Aero Conversion Kit #Y8860031. This will show you how to convert your Hullraiser to work on Aero bars.

view full answer...

Answer 3

Since you have a Yakima Hullraiser and need to fit them on aero bars the best solution is the Hullraiser Aero kit part #Y8860031 as this is what Yakima recommends. The MightyMounts are a great solution for other racks that don't have specific…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 7

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

Hi Alec, The Inno Kayak Roof Rack w/ Tie-Downs #INA452 needs a 28" minimum spread so that the saddles sit at the right spot for the kayak and support the weight properly. This is probably just a general guide from Inno though because the length…

view full answer...

Answer 10

Hey Alec, For your 2016 Ford Fusion I recommend the recommend a roof rack from Inno: Inno Aero Crossbars #INXB138-145 Inno Through Feet for Aero Crossbars #INXS250 Custom Fit Kit for Inno XS200, XS250, and INSU-K5 Roof Rack Feet #INK860 As with any…

view full answer...

Answer 11

There are a couple of differences between the two. The JetStream bars like #Y00425 are made of extruded aluminum while the CoreBars such as the #Y00421 you've looked at are constructed of galvanized steel. As you've mentioned, the CoreBar has…

view full answer...

Answer 12

The Rhino-Rack Heavy-Duty Roof Rack Roof Rack have specific C-channels that are designed to fit specific Rhino-Rack Heavy-Duty accessories, like the Rhino-Rack Hi-Lift Jack and Shovel-Holder Brackets #RRRCB-RSHB-RJHB as an example. That's the…

view full answer...

Yakima HullRaiser to HullRaiser Aero Conversion Kit on a Subaru Tribeca

Product Page this Question was Asked From

Continue Researching