Is Fascia Trimming Required to Install Curt Trailer Hitch on 2020 Cadillac XT4

Question

Question:

I see where it says you have to temporarily remove the bumper fascia to install the Curt hitch on my 2020 cadillac xt4. is there any cutting or trimming of this fascia to install?

asked by: Beth E

0

Expert Reply:

There is no type of fascia cutting or trimming necessary whatsoever to install the Curt Trailer Hitch Receiver # C39FR on your 2020 Cadillac XT4. The fascia has a removable panel which will allow you to access the trailer hitch when you need to and put the panel back on when you aren't using the hitch. The fact you can remove that panel and easily access the hitch is why you don't need to trim or cut any fascia.

I have added a link to the instructions for you to check out as well of the Curt Trailer Hitch Receiver # C39FR.

If you need a wiring harness to power your trailer's lights, the correct fit for your 2020 Cadillac XT4 is the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118795.

expert reply by: Kyle S

0

Answer 1

For your 2019 Cadillac XT4 the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C39FR is the correct fit. The installation details state the following for removing the fascia: a. Open the lift gate. b. Remove the plastic cover next to…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Is Fascia Trimming Required to Install Curt Trailer Hitch on 2020 Cadillac XT4

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching