Flange Dimensions of Bulldog Round A-Frame Jack # BD155157

Question

Question:

What are the flange dimesions of this bulldog jack?

asked by: Karl K

0

Expert Reply:

The 3 bolt holes of the Bulldog # BD155157 Jack are 3-1/4 inches apart on center. If you refer to the photo I edited for you, can can see all of the mounting plate dimensions.

expert reply by: Mike L

0

click to enlarge

Answer 1

?The distance from the mounting plate to the foot on the Trailer Valet JX-2K #TV54FR is 13" when fully retracted. The distance from the mounting plate to the top of the jack is 23". This jack can provide you with up to 14" of lift on…

view full answer...

Answer 2

The 3-bolt mounting flange on the Lippert Electric A-Frame Trailer Jack #LC285318 has a standardized hole pattern. This jack is intended to mount so that the included LED light faces forward toward the tow vehicle to illuminate the coupler and hitch…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 8

In order to match up the wheel studs for your Reliable 1206 hub, we'll need to know the full dimensions of the wheel stud you're replacing. In addition to the total length of the stud and its diameter and thread pitch, we'll also need to…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

The 205/65-10 and the 20.5 x 8-10 would be very close in size. Assuming that 20.5 is the diameter of the tire and 8 is the width. The Kenda 205/65-10 Bias Trailer Tire with 10 inch White Wheel, #AM3H390, for example, is 8.3 inches wide with a…

view full answer...

Flange Dimensions of Bulldog Round A-Frame Jack # BD155157

Product Page this Question was Asked From

Continue Researching